background image

Page 1 

 

General Information 

Thank you for purchasing this product. The purpose of this 

manual is to assist you in operating and maintaining your 

3-Point Sprayer.  

 

Retain a copy of your receipt for your unit,  

as it will be required to validate any warranty service 

Products are warranted against manufacturer or workmanship 

defects for one year from date of purchase for home owner  

usage and 90 days for commercial usage. 

 

For technical assistance, visit our website @ 

www.fimcoindustries.com or call: 

TOLL FREE @ 1-800-831-0027 

Our Technical Support Representatives will be happy to help you. 

To obtain prompt, efficient service, always remember to give the 

following information… 

 

Correct Part Description and/or part number 

 

Model #/Serial # of your sprayer 

Part descriptions and numbers can be obtained from the illustrated 

parts list section(s) of this manual. 

OWNER’S MANUAL

 

Assembly Instructions 

1. 

Install the tee valve sub-assembly to the 3-point carrier valve 

mount and position as shown in the exploded view. 

2. 

Slip the 1/2” bypass hose (from the relief valve) over the fitting 

on the bottom of the tank. Slide the hose clamp to the end of the 

hose and secure. 

Category I or II

 

Model: 200-3PT-1PC-TSC (2152285) 

(200 Gallon 3-Point Sprayer w/8-Row Boom, Handgun, Pump & Coupler

)

 

www.fimcoindustries.com 

1000 FIMCO Lane, P.O. Box 1700, North Sioux City, SD  57049      

Toll Free Phone: 800-831-0027 : Toll Free Fax: 800-494-0440 

[5008067   

 

 

 

 

 

(01/19)] 

3. 

Find the 1” x 36” pump feeder hose. Using a good quality 

thread sealant, carefully thread the 1” fitting into the strainer 

and the 3/4” fitting into the inlet side of the pump. Slip the hose 

all the way onto the fittings and secure with the hose clamps. 

4. 

Attach the 3/4” hose coming off the valve assembly to the out-

put side of the pump by threading the 3/4” fitting into the pump 

and securing with the hose clamp. Remember to use sealant. 

5. 

The roller pump IS included with the assembly. Attach the 

adapter, the torque chain and S-hook to a pump as needed. It is 

intended for your pump to be mounted directly to the tractor 

PTO. The torque chain needs to be secured to the tractor to 

keep your pump from spinning. 

6. 

Wrap the handgun hose around the hose hangers, which are 

attached to the tank straps. 

7. 

Using sealant thread the gauge into the top of the tee valve  

assembly. 

8. 

Mount the upright angles to the inside of the mounts on the 3-

point carrier using the supplied 1/2” bolts and nuts. Attach the 

backrack to the upright angles using the square U-bolts and 

nuts. Note: the backrack can be mounted in either a high or low 

position and the uprights can be adjusted for desired height. 

Attach the U-brackets as shown. 

9. 

Loosen the eye bolts and remove the 7” hinge bolts. Line up the 

outer booms and reassemble the hinge bolt through the outer 

boom yoke, the hinge casting and the spring connector. Tighten 

the eye bolt until the spring is at the desired tension. Lock the 

eye bolt in place with the inner whiz flange locknut. Bolt on the 

boom extensions using the 3/8” x 1-3/4” bolts and hex lock nuts. 

10.  Hook an end of each boom chain on an “S” hook attached to 

the top bar tube. Slip a slide clamp onto each outer boom. 

Place the other end of the boom chain between the ears of the 

slide clamp and secure with a 3/8” x 1” flange screw. Level the 

outer booms by moving the slide clamps in or out as needed. 

Tighten the bolts in the slide clamps to hold the clamps in place. 

11.  Attach the appropriate hose assemblies onto each of the three 

boom sections. The center section as five nozzles with “L” con-

nectors on each end. 

12.  Join the designated feeder hose from the tee valve sub-

assembly to each boom section and secure in place with hose 

clamps. 

Summary of Contents for 200-3PT-1PC-TSC











Reviews: