1
2 Sensitivity Indicator
3 Battery Save On/Off
4 Backlight On/Off
5 Fish Alarm On/Off
6 Battery Strength Indicator
7 Fish Depth Indicator
8 Fish Location Indicator
9 Bottom Contour Display
5.1 READING DEPTH
-4-
fig.7
4 OPERATION AND SETTING
fig.4
4.1 POWER ON/OFF
fig.1
3 DISPLAY VIEW
FISH FINDER
OPERATION GUIDE
5.2 FISH SHOW
-5-
-6-
-7-
-8-
2 HOW SONAR WORKS
-1-
-2-
4.3 CHANGE MEASURE UNITS FOR
DEPTH READINGS
fig.2
-3-
fig.5
fig.3
fig.6
Water Depth Display
1 PRODUCT OVERVIEW
5 FISH AND DEPTH READOUT
4.2 FUNCTION SETTING
Press and Hold the SETUP key for 3 seconds, the
Sensitivity indicator { } will blink; Pressing the SETUP key
repeating. (The indicator will blink for the current feature to
be set. Sensitivity{ } —SAVE{ }---Backlight{ }---
Alarm{ } )
Press the ENTER key to activate or deactivate a feature
The screen will automatically return to normal operation
after 5 seconds if no
key are pressed .
2
4 5
3
1
6
7
8
9
This product is
designed for the
liker in fishing
or the fisher.
The unit can be
used in the
river,the lake and
the sea.
It can help you to
find out the
location of the
fish, the depth of
water.
Especially,it can
find the shoal and
give a special
alarm to user!
Sonar technology is based
on sound waves. The
system uses sonar to loc-ate
and define structure, bottom
contour and composition, as
well depth directly below the
transducer.
The transducer sends a
sound wave signal and
determines distance by
measuring the time between
the transmission of the
sound wave and when the
sound wave is reflected off
an object;it then uses the
reflected signal to interpret
location, size, and
composition of an object.
Slide and remove the Battery Door , Install 4 AAA
batteries. Be certain to align the batteries as per the
diagram within the battery compartment.
Close the battery door completely .
Press the POWER key to turn the power On , the
unit enter normal mode after display full show 1
second.
Press and Hold the POWER key for 3 seconds to
turn the Power Off.
To enter the simulation mode: press and hold the
POWER key for 5 seconds and release while the
power is of.
NOTE:
The unit must be turned off to enter normal
operation from simulation mode.
Automatic power off feature : The display will shut off
automatically when the depth display reads “---
“continuously for 5 minutes.
Press and hold SETUP and ENTER at the same
time for more than 5 seconds,the display will flash
the current units setting.
NOTE:
*There are 5 -user Selectable sensitivity setting
to choose from. The sensitivity can be enhanced in dirty
or deep water. The sensitivity can be lowered in shallow
water. The function allows the detection more accurate.
* Backlight illuminated all the time when backlight
feature ON. This feature will greatly reduce the battery
life of the unit. So it should only be used during low
light conditions. The backlight will illuminate for 3
seconds whenever a key is pressed when the backlight
feature is set to off.
NOTE:
* You can select SAVE mode to work when you
play on long time or water quiet , in order to extend
batteries use-life.
* The screen can be refreshed by pressing the POWER
key during normal operation .
The depth readout on the down left will appear after the
power is turned ON and the sonar sensor is placed in
water. The depth meter will indicate”---“ if the depth
exceeds these parameters (2 feet to 328 feet / .7 to 100
meters).
Press SETUP key to choose M (M=Meters). Press
ENTER key to choose Ft (Ft=Feet )
The screen will automatically return to normal operation
after 5 seconds if no keys are pressed.
NOTE
: This reading may also occur in water is
extremely dirty, or where there are heavy silt or mud
bottoms. Sonar is a sound signal that travels
through water. Sonar will not travel through air. Keep
this in mind when sing the fish finder, as the fish
finder the smallest bubble between the sonar sensor
and the water, will cause the unit to not operate
correctly.
If the finder determines that sonar has detected a fish, the
display will show a fish shaped icon (figure 7). The first
column of fish indicators on the right of the display shows
the most current information. This column is then moved
to the left as a new reading is displayed. Fish icon moved
in every 5 seconds.
NOTE
:
The fish indicators move away from the right to the
left at a constant speed. This motion in no way
reflects actual movement of the fish.
