background image

 

 FLORIDA-PNEUMATIC.COM 

 

Please contact 1-800-356-3392 for further assistance.

Universal Tool

DIE GRINDERS

General Safety Information & Replacement Parts

WARNING:

 Risk of injury to persons. Read and 

understand operation instructions.  Always become familiar 
with all the instructions and warnings before operating any 
pneumatic tool.

TABLE OF CONTENTS

General Safety Information    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2 
Air Compressor and Air Tool Safety  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2-3 
Tool Specifications   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Installation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Maintenance / Lubrication   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4
Operation .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Troubleshooting   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Service Parts  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7-10 
Warranty   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 11
 

UT8728 / UT8729 

DIE GRINDER SERIES

UT8728E 

Extended Die Grinder

UT8728 

Die Grinder 

UT8729-12 
UT8729-18 

Angle Die Grinder 

Summary of Contents for Universal Tool UT8728













Reviews: