background image

FRIGOR MANUAL

 

GUIDE FOR INSTALLATION AND USE 

 

PROPER USE

 

The refrigerated cabinets as described in this operating manual are mainly intended for storing 
prepacked cooked meats,  delicatessen snacks (baguettes, sandwiches etc) beverages, prepacked 
salads, dairy products, fruit and vegetables. 

 

The siting of Frigor cabinets must be carried out by qualified technical personnel.  Do 

not load the cabinet with non-refrigerated products or use it to cool products. 

The products should be loaded in such a way that the correct rotation of the product is ensured. 

 

Variation in the configuration of the equipment and/or the use of elements added without the 
authorisation of Frigor, may cause incorrect operation. 

 

 

In the afore-mentioned product groups, only prepacked products with the following 
temperatures may be stored: 

Proper use only means the use as described above, adhering to the specifications on installation, 
operation and service.  Any other use is regarded as being contrary to specifications and is 
prohibited 
The Buyer responsibility to insure that the equipment will be fit for the purpose for which the 
Buyer intend to use the equipment. 

 

Do not operate in a room ambient temperature over 25 

°

C and 60% relative humidity. If the 

cabinet is to be operational in a room ambient over 25 

° 

C, air conditioning and an extract 

stem should be installed 

 

 

 

 

 

 

 

 

 

 

 

 

In the interest of continual product development we reserve the right to change any of the 

details and specifications without notice. 

Page 1 

‐ 

salad,

 

fruit

 

and

 

vegetables

 

+5

 

+10

 

C

 

‐ 

dairy

 

products

 

0

 

+7

 

C

 

‐ 

delicatessen

 

0

 

+7

 

C

 

‐ 

snacks

 

(e.g.sandwiches)

 

0

 

+7

 

C

 

‐ 

cooked

 

meat

 

0

 

+7

 

C

 

‐ 

cooked

 

poultry

 

0

 

+7

°

C

 

Summary of Contents for FBC-601

















Reviews: