GAL A X Y AUDIO
Quick Start Guide
ECM
Wireless Microphone System
Included Components
1.
ECM Receiver x1
3.
Power Supply x1
4.
Quick Start Guide x1
2.
1/4" Cable x1
1.
2
3
2
Setup
1
4.
2.
Insert the 5.5 mm plug into the DC
input jack, then plug the wall wart into a
120VAC outlet.
Press the “Select” button on the receiver
to choose a frequency number of 1-16.
Make sure the receiver is powered on.
(Powers on immediately when power
supply is plugged into the DC input jack)
1/4" Output: Connect 1 end of a shielded
1/4"M to 1/4"M cable to the receiver’s
1/4" output, then connect the other
end into your system input.
XLR Output: Connect a shielded
microphone cable to the receiver’s AF
XLRM output, then connect the other
end into your mixer input.
4.
3.
Operation
1
Optional Accessories
1.
HH52 Handheld Mic
3.
HS-U3BK Headset Mic
4.
LV-U3BK Lav Mic
AS-GTR Guitar Cable
5.
2.
MBP52 Body Pack
1.
2.
For detailed instructions for finding the best frequencies, please consult the online manual.
3.
5.
When the transmitter is synced, the RF
presence indicator will illuminate. When
talking into the microphone the AF
presence indicator will illuminate.
6
4
Then press ASC on the receiver.
Use the level control to adjust the
volume. This will affect both the XLR
and 1/4" outputs.
7
Place the chosen transmitter with it’s IR
window facing the receiver IR window,
about 6" away.
5
5b
Receiver IR Window Location:
Center of the receiver face
3
To sync the handheld mic transmitter,
make sure to power on first. For the body
pack, power on and then press the ASC
button.
5a
Transmitter IR Window Locations:
Handheld IR is located inside the battery
compartment. Body Pack IR is located
on the backside bottom corner.
The Mute Level is factory set and
normally needs no adjustment. However,
you may turn clockwise if interference is
present.
8
GAL A X Y AUDIO
Q
uick Start Guide
ECM
Wireless Microphone System
Included Components
1.
ECM Receiver x1
3.
Power Supply x1
4.
Quick Start Guide x1
2.
1/4" Cable x1
1.
2
3
2
Setup
1
4.
2.
Insert the 5.5 mm plug into the DC
input jack, then plug the wall wart into a
120VAC outlet.
Press the “Select” button on the receiver
to choose a frequency number of 1-16.
Make sure the receiver is powered on.
(Powers on immediately when power
supply is plugged into the DC input jack)
1/4" Output: Connect 1 end of a shielded
1/4"M to 1/4"M cable to the receiver’s
1/4" output, then connect the other
end into your system input.
XLR Output: Connect a shielded
microphone cable to the receiver’s AF
XLRM output, then connect the other
end into your mixer input.
4.
3.
Operation
1
Optional Accessories
1.
HH52 Handheld Mic
3.
HS-U3BK Headset Mic
4.
LV-U3BK Lav Mic
AS-GTR Guitar Cable
5.
2.
MBP52 Body Pack
1.
2.
For detailed instructions for finding the best frequencies, please consult the online manual.
3.
5.
When the transmitter is synced, the RF
presence indicator will illuminate. When
talking into the microphone the AF
presence indicator will illuminate.
6
4
Then press ASC on the receiver.
Use the level control to adjust the
volume. This will affect both the XLR
and 1/4" outputs.
7
Place the chosen transmitter with it’s IR
window facing the receiver IR window,
about 6" away.
5
5b
Receiver IR Window Location:
Center of the receiver face
3
To sync the handheld mic transmitter,
make sure to power on first. For the body
pack, power on and then press the ASC
button.
5a
Transmitter IR Window Locations:
Handheld IR is located inside the battery
compartment. Body Pack IR is located
on the backside bottom corner.
The Mute Level is factory set and
normally needs no adjustment. However,
you may turn clockwise if interference is
present.
8
GALAX Y AUDIO
Quick Start Guide
ECM
Wireless Microphone System
Included Components
1.
ECM Receiver x1
3.
Power Supply x1
4.
Quick Start Guide x1
2.
1/4" Cable x1
1.
2
3
2
Setup
1
4.
2.
Insert the 5.5 mm plug into the DC
input jack, then plug the wall wart into a
120VAC outlet.
Press the “Select” button on the receiver
to choose a frequency number of 1-16.
Make sure the receiver is powered on.
(Powers on immediately when power
supply is plugged into the DC input jack)
1/4" Output: Connect 1 end of a shielded
1/4"M to 1/4"M cable to the receiver’s
1/4" output, then connect the other
end into your system input.
XLR Output: Connect a shielded
microphone cable to the receiver’s AF
XLRM output, then connect the other
end into your mixer input.
4.
3.
Operation
1
Optional Accessories
1.
HH52 Handheld Mic
3.
HS-U3BK Headset Mic
4.
LV-U3BK Lav Mic
AS-GTR Guitar Cable
5.
2.
MBP52 Body Pack
1.
2.
For detailed instructions for finding the best frequencies, please consult the online manual.
3.
5.
When the transmitter is synced, the RF
presence indicator will illuminate. When
talking into the microphone the AF
presence indicator will illuminate.
6
4
Then press ASC on the receiver.
Use the level control to adjust the
volume. This will affect both the XLR
and 1/4" outputs.
7
Place the chosen transmitter with it’s IR
window facing the receiver IR window,
about 6" away.
5
5b
Receiver IR Window Location:
Center of the receiver face
3
To sync the handheld mic transmitter,
make sure to power on first. For the body
pack, power on and then press the ASC
button.
5a
Transmitter IR Window Locations:
Handheld IR is located inside the battery
compartment. Body Pack IR is located
on the backside bottom corner.
Place the chosen transmitter with it’s IR
window facing the receiver IR window,
about 6" away.
5
The Mute Level is factory set and
normally needs no adjustment. However,
you may turn clockwise if interference is
present.
6
