background image

© Copyright

Gallo Technologies

. All Right Reserved

- 1 -

061515V54RS

Operation & Installation Manual

(V- 55RS)

Keyless RFID Push Button Start & Security System

Keyless

Model # GTS-3RS (with Remote Start)

For Automatic Transmission only

DISCLAIMER:

This installation manual is designed for the professional installer with a good understanding of automotive electrical
systems, and if the vehicle is so equipped, the ability to disable the steering column locking mechanism. To ease in
proper installation, we recommend that the installer READ THIS MANUAL thoroughly before beginning the
installation. This manual is provided as a GENERAL GUIDELINE and the information contained herein may differ
from your vehicle. Gallo Technologies and its’ vendors shall not be liable for any accident resulting from the misuse
of this product.

GTS-3RS is not to be used in a manual Transmission vehicle

. This product is designed to be

professionally installed into a vehicle in which all systems and associated components are in perfect working
condition. DAMAGE to the GTS-3RS unit resulting from incorrect installation or failure to follow guidelines stated in
this manual, will not be covered under warranty and will be subject to repair or replacement charges. Links to
nation-wide Alarm installers can be found on our web site at

www.GalloTech.com

.

Table of Contents

1.1 Introduction (page 2)
1.2 Key FOB Operation (page 3)
1.3 “Start Stop Engine” Button Operation (page 4)
1.4 Remote Start Setup & Operation (page 6)
1.5 Function Options (page 7)
1.6 Key FOB & Program Function Setup (page 8)
1.7 Installation Instructions (page 10)
1.8 Final Installation (page 15)
1.9 Troubleshooting (page 16)

www.GalloTech.com

Summary of Contents for GTS-3RS

















Reviews: