background image

ASSEMBLY DRAWING

Enriching Childhood Through Play

O

C

M

C

A P L A Y

E

O R

SM

R

P A N Y

ISSUED/REVISED:

1−800−235−2440

INSTALLATION

PARTS LIST

DETAIL

REFERENCE

=

=

R

10777

TIRE

SWING

06/20/05

NOTE:  10778  ADD−A−BAY

10777 SHOWN

3

1

3

2

113

113

562

114

116

0'-12 1/2" [31.75cm]

FROM FINISHED SURFACE

TO BOTTOM OF TIRE

6'-8"

 [203

.20c

m]

FIN

ISH

ED S

URF

ACE

C O

F TO

PRA

IL

L

NOTE:  REGULAR MAINTENANCE 
REQUIRES LUBRICATION OF SWIVEL 

ASSEMBLY WITH STANDARD 
AUTOMOTIVE GREASE.  A GREASE 

FITTING IS INCLUDED IN THE 

SWIVEL ASSEMBLY FOR THIS 

PURPOSE.  IN AREAS OF HIGH USE, 
LUBRICATION INTERVALS SHOULD 
BE INCREASED ACCORDINGLY.

STEP 1:  

Before assembling this equipment, 

read the enclosed 

Installer Instructions

 in the 

installation booklet; follow all the instructions 

during installation. 

STEP 2:  

Assemble parts as shown in the 

Assembly Drawing.

  Refer to the assembly 

details for the specific hardware required in 
each connection. 

STEP 3:  

Loctite (supplied by others) should be 

used on all threaded hardware.

INSTALLATION 
INSTRUCTIONS

YEARS OLD

Summary of Contents for Tire Swing







Reviews: