background image

Version 1.0 

Replacing GTS 8000 on Citation M2 

 

Garmin G3000 Software Version 10

 

 

Caution:  Before starting the software or configuration loading process, certain 

items may be required to be recorded first, to prevent loss of 

information or settings. See Section 1 for details. 

 

Caution:  Make certain that all SD cards are available before starting. These are 

usually located in a blue pouch onboard the aircraft (usually in AFM). 

 

Caution:  Follow all steps in a given section for specific loadings. Failure to do so 

will result in probable rework. 

 

Caution:  Ensure that power is available through a GPU so that power is not 

interrupted during the loading process.

 

 

Note: 

This document is to supplement, not replace, the Cessna Citation M2 

MM, and Garmin G3000 LMM. 

 

Note: 

Reference latest revision of the Garmin G3000 LMM 190-01668-00.

 

 

Table of Contents 

 

Introduction 

G3000 System Familiarization 

Section 1   

References Prior to Certain Software and Configuration Loading 

Section 2   

Software and Configuration Loading 

Section 3   

Aircraft Configuration 

Section 4   

Final Verification / Return to Service 

Section 5   

Troubleshooting 

Appendix A 

Determining Options Installed 

Appendix B 

Configuration ID / CRC Numbers

 

 

 

 

Summary of Contents for GTS 8000

















Reviews: