background image

1

www.gateway.com

Replacing the AC Adapter

Technical Support

See the label on the bottom of the notebook for Customer 
Care Information. See your hardware guide for important 
safety, regulatory, and legal information.

© 2006 Gateway, Inc. All rights reserved. Gateway and 
eMachines are trademarks or registered trademarks of 
Gateway, Inc. in the United States and other countries. 
All other brands and product names are trademarks or 
registered trademarks of their respective companies.

Replacing the AC Adapter

To connect the AC adapter:

1

Connect the power cord to the AC adapter.

2

Connect the AC adapter to your notebook’s power 
connector.

3

Plug the power cord into a wall outlet. The battery 
charge indicator turns on.

If the battery charge indicator does not turn on, 
unplug the adapter from your notebook, then plug 
it back in.

Caution

Replace the power cord if it becomes damaged. 
The replacement cord must be of the same type 
and voltage rating as the original cord or your 
notebook may be damaged.

Warning

Do not attempt to disassemble the AC adapter. 
The AC adapter has no user-replaceable or 
user-serviceable parts inside. The AC adapter 
has dangerous voltages that can cause serious 
injury or death. Contact Gateway about returning 
defective AC adapters.

Important

If the battery charge indicator does not turn blue 
after three hours, contact Gateway Customer 
Care at the Web address or telephone number 
shown on the label on the bottom of your 
notebook.

Battery charge indicator

Summary of Contents for M255











Reviews: