background image

 (EAN)

Evolve

 

LED Area Light

BEFORE YOU BEGIN

Read these instructions completely and carefully.
Save these instructions for future use.

• This luminaire is designed for outdoor lighting service,

and should not be used in areas of limited ventilation,
or in high ambient temperatures.

• Best results will be  obtained if installed and  maintained

according to the  following  recommendations.    

• Luminaire is designed to operate in ambient    
  temperatures ranging from -40°C to 50°C 

and to be mounted   horizontally to a vertical pole
with LEDs facing down.

WARNING

Risk of electrical shock.  Disconnect power before servicing 

or installing product.

GE

Lighting

Installation Guide

GEH-6032

imagination at work

SPECIFICATIONS

• Weight: Maximum weight <20.5 lbs  (9.3 kg)
• EPA: Horizontal mounting:  0.67 sq ft max (0.06 sq M)
• IP Rating: Optical 66, Standard Electrical Enclosure:

UL 1598 Wet Location Rated

CAUTION

Risk of injury.  Wear safety glasses and gloves during 

 installation and servicing.

WARNING

Risk of injury or damage.  Unit will fall if not installed 

 properly.  Follow installation instructions.

WARNING

Risk of fire. Use supply wire specified on nameplate.

This device complies with Part 15 of the FCC Rules.  Operation is 

subject to the  following two conditions:  (1) This device may not cause 

harmful  interference, and (2) this device must accept any 

interference received,  including interference that may cause 

undesired operation. 

This Class [A] Lighting Equipment complies with 

Canadian standardICES-005[A] / NMB-005[A].  

 

Note: This equipment has been tested and found to comply with the 

limits for a Class A digital device, pursuant to part 15 of the FCC Rules. 

These limits are  designed to provide reasonable protection against 

harmful  interference when the equipment is operated in a  commercial 

 environment. This equipment  generates, uses, and can radiate  radio 

frequency energy and, if not installed and used in  accordance with 

the instruction manual, may cause harmful interference to radio 

 communications. Operation of this equipment in a residential area 

is likely to cause harmful  interference in which case the user will be 

required to correct the  interference at his own expense.

Summary of Contents for Evolve













Reviews: