1
To assemble the tree top,
properly insert the "TOP"
section into the top of
section "B". (See Fig. D)
Adjust branch tips, as needed,
for a fuller look.
7
Carefully unpack the carton.
Remove bubble wrap and
inspect the sections of your tree.
The carton should include sections
"A", "B" and "Top", as well as
a Tree Stand.
2
3
The tree stand should be open and
set at 90° angle.
90°
Insert Section A into tree stand,
tighten the thumbscrew. Then
insert the plug into an electrical
wall outlet.
Nicolas Holiday Ltd. thanks you for purchasing this pre-lit Christmas
tree. Should you have any problems with your tree, visit us at
www.geholidaylighting.com
for more information. You can call our
toll free number at 1-877-398-7337.
Check our website for latest service hours and assembly instruction videos.
IMPORTANT:
Store your carton neatly in a cool, dry location protected from sunlight
to prolong the tree life and to better keep the light sets in working order. Do not place
a heavy load on the carton to avoid damage to or crushing the carton and tree inside.
NOTE:
No tools required
7.5 FT TREE
Tree Storage
1. Remove the tree’s main extension cord
plug from the wall outlet.
2. Starting at the top, disconnect the "TOP"
from section "B" and then disconnect
section "B" from section "A".
{Fig. 1}
Note:
Gently fold the tips in branches
and fold the branches
up toward the center.
{Fig. 2}
Care should be taken to avoid
damage to the lights.
3. Remove section "A" from the tree stand
and close tree stand to place into the carton.
4. Refer to the drawing on how to repack
your tree.
{Fig. 3}
DISCLAIMER :
DO NOT USE OR INSTALL ANY ADDITIONAL CHRISTMAS LIGHTING
OR ORNAMENTATION THAT IS POWERED BY A LIGHT BULB SOCKET. DOING THIS
MAY RESULT IN DAMAGE TO YOUR CHRISTMAS TREE OR CAUSE PERSONAL
INJURY. DOING THIS, WILL RESULT IN A VOID OF THE LIMITED WARRANTY OF
THIS PRODUCT.
Disconnect the decorative item from the power source before
performing any maintenance or cleaning.
Troubleshooting Tips
If the tree does not illuminate, make certain the wall switch is turned on.
If one section of your tree does not illuminate, check that section for loose
or missing bulbs, all factory connections are properly made or that you
properly made all the electrical connections between each tree section,
Also, check the fused plug for a missing or burned out (open) fuse.
4
Untie RED twist-tie to release branch
panels. All branches should fall into
place with a gentle pull on the outer
layer of branches.
Fig. A. Start at the inner and stagger
the tips. Move each tip up to 40°.
Fig. B. Make tips 2 & 3 to horizontial,
tip 4 to vertical and tips 5 and 6
up to 45°.
B
A
TOP
2
3
1
Thumbscrew
To assemble the section "B",
properly insert section "B"
into the top of section "A".
(See Fig. C)
Adjust branch tips, as needed,
for a fuller look.
5
Repeat “Step 4” for shaping.
6
For indoor use only
120V
THIS IS NOT A TOY, FOR DECORATIVE USE ONLY.
GE is a trademark of General Electric Company
and is under license by Nicolas Holiday Ltd.
©2022 Nicolas Holiday Ltd.
9 F., No. 37, Guangfu North Rd., Taipei, Taiwan 10560 All rights reserved.
Printed in China
22003LO
6 pcs
3-amp
3 pcs
Qty
Spare parts
included
Tree Sections
Tree Stand
Approx. Asm Time*
7.5 ft tree
3
Metal
10 – 15 minutes
TREE ASSEMBLY DIAGRAM
7.5 FT
TOP
B
A
SCHEMATIC DIAGRAM
Tree Stand
OPEN
Fig. C
Fig. D
Pre-Lit Christmas Trees
Assembly Instructions
A
40°
1
B
90°
90°
45°
2
3
4
5
6
Tree top
connector
TOP
A
B
Tree Stand
To electrically connect the sections, fully
insert the plug from the extension cord
attached to the pole of the middle
section into the extension cord outlet
attached to the pole near the top of
the bottom section.
To illuminate the top, fully insert the plug
from the top section into either the end
connector or the extension cord outlet
on or near the top layer of branches of
previously assembled pole.
