LED 500 8MM LIGHTS
FOR INDOOR USE ONLY
IMPORTANT SAFETY INSTRUCTIONS
When using electric products, basic precautions should always be followed including the following:
a)
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let lamps rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, when retiring for the night, or if left unattended.
h) This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
l) Do not cover the product with cloth, paper or any material not part of the product when in use.
m)This product is equipped with push-in type lamps. Do not twist lamps.
n) Read and follow all instructions that are on the product or provided with the product.
o)
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
a) When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on
live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
b) If the product is placed on a tree, the tree should be well secured and stable.
c) Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or
frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
d) When storing the product, carefully remove the product from wherever it is placed, including tree, branches,
or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
e) When not in use, store neatly in a cool, dry location protected from sunlight.
CAUTION:
1. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp
burns out. Do not replace lamps with other than the spare lamps provided with this product.
2. To reduce the risk of fire and electric shock: a) Do not install on trees having needles, leaves or branch
coverings of metal or materials which look like metal, and b) Do not mount or support strings in a manner
that can cut or damage wire insulation.
USER SERVICING INSTRUCTIONS
Replace the lamp.
1. Grasp plug and remove from the receptacle or other outlet device.
Do not unplug by pulling cord.
2. Pull lamp and plastic base straight out of lampholder.
3. Replace lamp with only 3.6 Volt, 0.072 Watt,
LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
a) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
b) Thread leads of new lamp through holes in old base with one lead in each hole.
c) After lamp is fully inserted into base, bend each lead up, like other lamps in the
light set so that the leads will touch the contacts inside the lampholder.
Operate the Remote:
1. Pull out the plastic film from the battery cover
to energize the remote. {Fig. 1}
2. The remote has
t
en buttons {Fig. 2}
a. ON/OFF – Turn set ON/OFF
b. FUNCTION – Press to change the light pattern.
NOTE:
Choose function then color.
3. The effective operating distance of the remote is 33
'
(10m)
BATTERY CAUTION:
• Always purchase the correct size and grade of battery most suitable for the intended use.
• Replace only with lithium, type CR2032 battery.
• Clean the battery contacts and also those of the device prior to battery installation.
• Ensure the battery is installed correctly with regard to polarity (+ and -).
• Remove battery from equipment which is not to be used for an extended period of time.
• Remove used battery promptly.
Warning:
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at 1-877-398-7337
or visit us on the web at
www.geholidaylighting.com
FP-18 PRINTED IN CHINA
©2018 Nicolas Holiday Inc., 204 Spring Hill Road Trumbull, CT 06611
9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights reserved.
MODEL NO.
18232HD
Fig.2
OUTSIDE OF COMPARTMENT
INSIDE OF COMPARTMENT
