background image

 

P/N 466-5234 

• REV A • 06APR16   

 

Simon

® 

XTi Installation Guide

Content 

Contact information......................................................... 1

 

Description ...................................................................... 1

 

Installation ....................................................................... 1

 

Connecting hardwired devices ....................................... 2

 

Wiring phone lines .......................................................... 3

 

Wiring the power transformer ......................................... 4

 

Resetting memory to factory defaults ............................. 4

 

Programming .................................................................. 5

 

Status & Settings screen ................................................ 5

 

Sensors ........................................................................... 7

 

Cleaning the touch screen ............................................ 10

 

Disposal ........................................................................ 10

 

Specifications ................................................................ 10

 

Regulatory information.................................................. 10

 

Contact information 

www.utcfireandsecurity.com or www.interlogix.com 

For customer support, see www.interlogix.com/contact 
 
All trademarks are the property of their respective owners. 
Interlogix is part of UTC Climate, Controls & Security, a unit of 
United Technologies Corporation. 

© 2016 United Technologies Corporation. All rights reserved  

 

Description 

This is the Installation Guide for the Simon® XTi system 

(models 600-1054-95R-16 and 600-1054-95R-16-CN). 

Table 1: Sensors and recommended sensor groups 

Device 

Part number 

Recommended 
sensor group 

Indoor motion sensor 

60-639-95R, 60-807-
95

 b

 

15, 17, 18, 20, 28, 
or 32  

Entry/exit door 

60-362N-10-319.5 

10 

Interior door 

60-362N-10-319.5 

14 

Door/Window sensor 

60-362N-10-319.5 

13 

Smoke sensor 

TX-6010-01-1 

c

 

26  

Glassbreak sensor 

60-873-95

 b

 

13  

4-Button Key fob 

600-1064-95R 

b

 

01   

Device 

Part number 

Recommended 
sensor group 

Simon XT Talking 
Touch Screen 

60-924-3-XT-2WTTS 

b

 

60-924-RF-TS 

 d

 

00, 01, 04, 05, 06, 
or 07 

Simon XT Talking 
Touchpad  

60-924-3-XT 

b

 

01 

Carbon Monoxide alarm  TX-6310-01-1

 b

, 600-

6520-95 

b

 

34  

a. 

Not certified as a primary protection circuit for UL-listed 
systems and is for supplementary use only. 

b. 

Has not been investigated by UL. 

c. 

Required for UL-listed residential fire alarm applications. 

d. 

The TWTTS has been verified for use by ETL. Neither this 
device nor other devices that employ the UTCFS 80 Bit 
Enhanced Protocol have been investigated for use by UL. 

Note

: These sensor groups are only recommendations. The installer 

should choose the correct sensor group for the application. 

 

CAUTION: 

Do not use outdoor motion sensors for 

intrusion protection.

 

ATTENTION: 

N’utilisez pas des détecteurs de mouvement 

extérieurs pour détecter les intrusions. 

Safety information 

 

IMPORTANT SAFETY INFORMATION. READ ENCLOSED 

WARNINGS AND SAFETY INFORMATION. 

 

WARNING: CHOKING HAZARD

. The product accessory 

bag contains items that could be choking hazards. Please keep 
away from small children. 

AVERTISSEMENT: Le sachet d'accessoires produit contient 
des éléments qui pourraient être les dangers d'étouffement. 
Veuillez garder hors de la portée des jeunes enfants. 

 

WARNING: 

Disconnect panel power before servicing.  

AVERTISSEMENT: Débrancher l'alimentation du panneau 
avant l'entretien. 
 

CAUTION

: Use static electricity precautions when handling 

electronic components.  

ATTENTION:  Utiliser les précautions de l'électricite statique 
lors de la manipulation des composants électroniques

Summary of Contents for Simon XTi













Reviews: