background image

Booster Power Supply

Manual

DEVELOPED BY

General Signal Building Systems Corporation
6411 Parkland Drive
Sarasota, FL 34243
(941) 739-4300

COPYRIGHT NOTICE

Copyright © 1999 General Signal Building Systems Corporation

This manual and the products it describes are copyrighted by General Signal
Building Systems Corporation. You may not reproduce, translate, transcribe, or
transmit any part of this manual without express, written permission from
General Signal Building Systems Corporation.

LIMITATION OF LIABILITY

This product has been designed to meet the requirements of NFPA Standard 72,
1996 Edition; Underwriters Laboratories, Inc., Standard 864, 7th Edition.
Installation in accordance with this manual, applicable codes, and the
instructions of the Authority Having Jurisdiction is mandatory. General Signal
Building Systems Corporation shall not under any circumstances be liable for
any incidental or consequential damages arising from loss of property or other
damages or losses owing to the failure of General Signal Building Systems
Corporation products beyond the cost of repair or replacement of any defective
products. General Signal Building Systems Corporation reserves the right to
make product improvements and change product specifications at any time.

While every precaution has been taken during the preparation of this manual to
ensure the accuracy of its contents, General Signal Building Systems
Corporation assumes no responsibility for errors or omissions.

FCC WARNING

This equipment can generate and radiate radio frequency energy. If this
equipment is not installed in accordance with this manual, it may cause
interference to radio communications. This equipment has been tested and
found to comply within the limits for Class A computing devices pursuant to
Subpart B of Part 15 of the FCC Rules. These rules are designed to provide
reasonable protection against such interference when this equipment is operated
in a commercial environment. Operation of this equipment is likely to cause
interference, in which case the user at his own expense, is required to take
whatever measures may be required to correct the interference.

COMPATIBLE DEVICES

For a complete list of compatible devices, refer to P/N 85000-0285.

DOCUMENT HISTORY: P/N 270946

Date

Revision

Reason for change

June 1999

1.0

Initial release.

July 1999

2.0

Added note to AC power wiring diagram and updated
specifications.

Technical Manuals Online! - http://www.tech-man.com

Summary of Contents for BPS10



















Reviews: