background image

 

THE GIANT-VAC 

‘PTO BLOWER’ 

MODELS 2000*/3200**/4000*** 

 

ASSEMBLY INSTRUCTIONS AND OPERATOR’S MANUAL 

 

Congratulations! 
 

You have just purchased one of the finest pieces of outdoor power equipment on the 
market today.  If properly cared for, your Giant-Vac PTO Blower will provide years of 
dependable service.  Please read and follow this instruction manual carefully in order to 
get the most out of your new equipment. 
 
First, inspect your machine upon delivery. Each Giant-Vac product leaves our factory in 
excellent condition; occasionally, however, some damage may occur during shipment.  If 
any such damage is found upon initial inspection, 

immediately

 notify the transport carrier 

who delivered your machine, as they are solely responsible for the damage as well as 
any subsequent adjustments.  
 
Your Giant-Vac PTO Blower requires very little assembly.  Simply follow the instructions 
contained within this manual to begin enjoying the benefits of your new unit.  

 

CALIFORNIA PROPOSITION 65 WARNING

 

 

Gasoline and Diesel engine exhaust and some of its constituents are 

known to the State of California to cause cancer, birth defects and other 

reproductive harm. 

 

As an owner of off-road gasoline or diesel engine equipment and/or as an 

employer, you also may have an obligation under the California 

Occupational Safety and Health Act or under Proposition 65 to warn 

persons exposed to gas and diesel engine exhaust and/or other 

Proposition 65 chemicals in and around your workplace.  See California 

Health and Safety Code section 25249.5, Title 22 of the California Code of 

Regulations at Section 1200 

er seq.,

 and Title 8 of the California Code of 

Regulations Section 5194. 

 

*   Model 2000 P.T.O. Blower is designed to be used in conjunction with a P.T.O. 3-point hitch tractor equipped with an 
18-25HP P.T.O. drive that can achieve 540 R.P.M.  
 
** Model 3200 P.T.O. Blower is designed to be used in conjunction with a P.T.O. 3-point hitch tractor equipped with a 25-
38HP P.T.O. drive that can achieve 540 R.P.M.  
 
***Model 4000 P.T.O. Blower is designed to be used in conjunction with a P.T.O. 3-point hitch tractor equipped with a 
40+HP P.T.O. drive that can achieve 540 R.P.M.  

REV. B – 8/00 

 
 
 

Summary of Contents for 2000 series















Reviews: