Giant AC BIKES-2001 Owner'S Manual Download

Page: 1 / 10

- Pag. 1. -

AC TEAM

Model Year 2001

Owners Manual

October 2000.

Contents:

Introduction.

Sizing.

Rear suspension
3-1. Adjusting travel
3-2. Coil over shock
3-3.

Rear suspension tuning

3-4.

“SAG” adjustment

3-5.

Damping adjustment

3-6.

Changing the coil spring

3-7.

Removing the rear shock assembly or pivots.

Chain tension device
4-1. Assembly.

Cleaning and maintenance.

ALL CONDITIONS MOUNTAIN BIKE

•

Multi purpose, extreme riding mountain bike

•

(Semi-) downhill, Dual Slalom

•

Frame compatible for chain tension device (included), bash ring, 2.2” tires

•

MPH hydraulic disc brakes

•

Front fork with lock out

•

Coil over rear shock unit (included)

•

Sealed bearings on all pivots

•

3 rear shock positions

•

Rear wheel travel: 6~5¼~4½ inches, front wheel travel: 125 mm.

Summary of Contents for AC BIKES-2001











Search results

Summary of Contents for AC BIKES-2001

Reviews:

Related manuals for AC BIKES-2001

Brands by name

Popular brands

Giant AC BIKES-2001, Owner'S Manual

Search results

Summary of Contents for AC BIKES-2001

Reviews:

Related manuals for AC BIKES-2001

Brands by name

Popular brands