W131-X30 Quick Installation Guide
Pre-installation Cautions
Make sure the system is not turned on or connected to AC power.
Always handle boards carefully. They can be extremely sensi-tive to electrostatic discharge (ESD). Hold boards only by their edges.
After removing a board from its protective wrapper or from the system, place the board component side up on a grounded, static free surface.
Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface.
Risk of explosion if battery is replaced incorrectly or with an incorrect type. Replace the battery only with the same or equivalent type recommended
by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
No.
Code
Description
1
MLAN
Server managemnt LAN port
2
USB2_LAN1
LAN port #1 (top) / USB 3.0 ports (bottom)
3
USB2_LAN2
LAN port #2 (top) / USB 3.0 ports (bottom)
4
COM1_VGA
Serial port (top) / VGA port (bottom)
5
PMBUS
PMBus connector
6
SYS_FAN1
System fan connector#1
7
P12V_AUX
8 pin power connector (for CPU)
8
CPU_FAN
CPU fan connector
9
SYS_FAN2
System fan connector#2
10
ATX1
24 pin main power connector
11
SD_CN
SD card connector
12
SATA_4
SATA 3 6Gb/s connector
13
SATA_5
SATA 3 6Gb/s connector
14
SATA_2
SATA 3 6Gb/s connector
15
SATA_3
SATA 3 6Gb/s connector
16
SATA_1
SATA 3 6Gb/s connector
17
SATA_0
SATA 3 6Gb/s connector
18
FP_2
Secondary front panel header
19
FP_1
Front panel header
20
F_USB2
USB 2.0 header
21
IPMB
IPMB connector
22
TPM
TPM connector
23
BP_1
HDD back plane board header
24
COM2
Serial port cable connector
25
PCIE_1
PCI Express x8 slot (running at x4)
26
PCIE_2
PCI Express x16 slot (running at x8)
27
BAT
Battery socket
28
PCIE_3
PCI Express x1 slot
29
PCIE_4
PCI Express x16 slot (running at x8)
30
LED_BMC1
BMC firmware readiness LED
Motherboard Components
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
30
25 26 28
27
29
ME
Force
Update
ME_UPDATE
Default
Enable
3
2
1
Clear
CMOS
CLR_CMOS
Enable
Default
S3
Power On
Select
S3_MASK
3
2
1
Default
Enable
Password
Clear
BIOS_PWD
Default Enable
1 2 3
Default Enable
1 2 3
ME
Recovery
ME_RCVR
Default Enable
1 2 3
BIOS
Recovery
BIOS_RCVR
CPU
DIMM_P0_A0
DIMM_P0_A1
DIMM_P0_B0
DIMM_P0_B1
System Components
Front Bezel Door
2
3
4
5
6
3
1
No. Desription
1
Optical disc drive (Option)
2
Front bezel door
3
Hard Disk Drives
4 Motherboard
5
PCIe card bay
6
Power supply module
System Cover
1
1
2
3
1
2
PCI Express Card
Power Supply
1
2
Hard Disk Drive
Optical Disc Drive
1
2
1
2
1
2
Installing CPU/
安装
CPU
1
2
NOTE!
Remove side cover before removing
the front bezel door
Memory Population Configuration/
安装内存
All channels in system run at the fastest common frequency.
Mixing ECC and non-ECC UDIMMs anywhere on the platform is not supported.
1 and 2 DPC is supported at 2133MHz.
所有通道模式以最快的频率速度运行。
此主板不支持ECC与非ECC内存模组混合使用。
1
与
2 DPC
均支持
2133MHz
速度
。
Type
Ranks Per
DIMM and
Data Width
Speed (MT/s);
Slot Per Channel (SPC) and
DIMM Per Channel (DPC)
Supported
Voltage
2 Slot Per Channel
1DPC
2DPC
UDIMM
Unbuffered
DDR4 ECC
UDIMM
Unbuffered
DDR4 non-ECC
SR
1.2V
1.2V
2133
2133
DR
2133
2133
No. Desription
1
USB 2.0 ports
2
Power button with LED
No. Desription
1
Power supply module cord socket
2
Serial port
3
VGA port
4
USB 3.0 ports
5
GbE LAN ports
6
10/100/1000 Server management LAN port
7
PCIe card bay
System Appearance
Off
State
Description
Yellow On
1Gbps data rate
Green On
100Mbps data rate
10Mbps data rate
10/100/1000 LAN LED:
Speed LED Link/Activity
LED
1
2
1
2
3
4
5
6
7
Power button/ LED:
Green On
Off
Description
System is powered on.
System is not powered on or in ACPI S5 state (power off)
System is in ACPI S4 state (hibernate mode)
State
PN:12xx
Summary of Contents for W131-X30
Page 2: ......
