GMC 40L Instruction Manual Download

Page: 1 / 16

40L & 50L

VERTICAL

DIRECT DRIVE

AIR COMPRESSORS

EVAC40 & EVAC50
INSTRUCTION MANUAL

Black

Cyan

Magenta

Yellow

Code:

EVAC40/50 IM

Date:

070912

Edition:

Op:

DCR

Do not switch on

for the first time

without first

filling with oil.

��

Air discharged from

this unit is not

suitable for human

consumption.

��

Test the safety relief

valve daily.

Refer the instruction

manual.

��

Keep oil level as shown:

Use only oil grade

specified in instruction

manual.

��

To prevent build-up of

condensation, open

drain cock daily

When filter becomes
dirty or oily, clean or

replace filter. Refer to

instruction manual.

��

High voltage used on

this equipment. Switch

off power supply &

remove plug from mains

before removing any

covers. Ensure mains

outlet is adequately

rated for this unit.

��

Unit starts

automatically.

Switch off power supply,

remove plug & relieve

air pressure prior to

commencing service

tasks.

��

Read instruction manual

prior to starting unit.

This equipment

operates from

AC mains only.

Summary of Contents for 40L

















Search results

Summary of Contents for 40L

Reviews:

Related manuals for 40L

Brands by name

Popular brands

GMC 40L, Instruction Manual

Search results

Summary of Contents for 40L

Reviews:

Related manuals for 40L

Brands by name

Popular brands