background image

1

GENERAL INFORMATION

INSTALLER! PLEASE LEAVE WITH HOMEOWNER

INSTALLATION AND OPERATING INSTRUCTIONS

This appliance is to be burned only in an approved woodburning Fireplace with adequate chimney draft.
When burning, the chimney damper must be 

FULLY OPEN

.

This appliance must be installed in a fireplace which operates
properly when wood fires are burned.

 

For best results, natural gas pressure must be 7” to 10-1/2” water

column.

 

If used with glass fireplace doors, burn with doors in open position.

 

Do not burn wood or other items with this appliance.

Please Note: It is important that you read instructions before installing or operating this appliance

MANUFACTURED BY:

4301 WESTGROVE DRIVE

ADDISON, TX 75001

The installation, including provisions for combustion and
ventilation air, must conform with local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1-1988 and NFPA54-1988.

The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system when testing
at test pressures in excess of 1/2 psig.

The appliance must be isolated from the gas supply piping
system by closing its individual manual shutoff valve during
any pressure testing of gas-supply system at test pressures
equal to or less than 1/2 psig. This is accomplished by closing
the gas supply line valve, which is required by NFPA 54,
section 5.54

The minimum inlet gas supply pressure for the
purpose of input adjustment is 7” WC for Natural Gas
and 11” WC for Propane Gas.

The maximum inlet gas supply pressure for this burner
is 10.5” for Natural Gas and 13” for Propane Gas.

This appliance is designed for use with Natural Gas unless clearly labeled for Propane (LP). Never use Propane Gas in an
appliance designed for Natural Gas or Natural Gas in an appliance designed for use of Propane Gas.

FOR YOUR SAFETY

If you smell gas:
1. Open Windows.
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

IMPORTANT INFORMATION

CHECK TO BE SURE APPLIANCE IS FOR PROPER GAS TYPE.

Summary of Contents for ALB24NAT







Reviews: