background image

Pairing the Goldtouch Comfort Mouse

1. From Control Panel, double-click “Bluetooth Devices”. 
2. From the Bluetooth Devices window, press the “Add” button.
3. Ensure the mouse is turned on and in pairing mode by pressing 

the recessed button on the bottom of the mouse.
4. From the Add Bluetooth Devices window, please follow the 

instructions, and click the checkbox next to “My device is setup and 

ready to be found.”
5. Once the device is detected, select the Goldtouch Comfort 

Mouse and click “Next”.
6. When prompted for  a passkey, click the radio button for “Don’t 

use a passkey”. and click “Next”.
7. The wizard will connect to the device and the “Add Bluetooth 

Device” wizard will complete.  To close the wizard, click “Finish”.

Pairing the Goldtouch Comfort Mouse

Ensure the mouse is turned on and in pairing mode by pressing the 

recessed button on the bottom of the mouse

1. From the Start screen, fetch the Charms bar, click the Settings 

icon, and click the Change PC Settings button.
You can summon the Charms bar’s Settings pane in any of three  

ways:

Mouse: Point the cursor at the screen’s top- or bottom-right    

corner.
Keyboard: Press I and press Enter.
Touchscreen: Slide your finger from the screen’s right edge 

inward.

2. Press the Pairing Button on the bottom of the Mouse for 2-3 sec-

onds, until the Red Sensor light it blinking to indicate pairing mode.
3. From the Devices category, click the Add a Device icon.
4. Once the device is detected, select the Goldtouch Comfort Mouse 

and click “Pair”.
5. The wizard will connect to the device and the “Add Bluetooth 

Device” wizard will complete.  Wait until your computer tells you 

that the drivers have successfully installed before using your mouse. 

To close the wizard, click “Finish”.

Goldtouch Bluetooth Mouse Install Guide

The Goldtouch Comfort Mouse is designed to utilize Microsoft 

and Apple’s built-in support for Bluetooth devices.  There are 

no third-party drivers required to use the Goldtouch Comfort 

Mouse.  This Quick Install Guide will walk  you through the 

steps required to pair your new Bluetooth mouse with your 

computer.

The Goldtouch Comfort Mouse is compatible with any embed-

ded or third-party Bluetooth adapter.

If your computer has a built-in Bluetooth adapter, then the       

optional Goldtouch Bluetooth adapter is not required.  

To put the mouse in pairing mode, simply press the recessed 

button on the bottom of the mouse using a paperclip or the 

tip of a pen.

1.  From the task bar, right click the Bluetooth icon and click

"Add a Bluetooth Device," or go to PC Settings \ Bluetooth and 

Other Devices. 
2.  Press the Pairing Button on the bottom of the Mouse for 2-3 

seconds until the Red Sensor light is blinking to indicate pairing 

mode. Note: You may or may not see a blinking sensor depending 

on your lighting conditions. 
3. From the "Bluetooth and Other Devices" screen, click "Add 

Bluetooth or Other Device." Select the Goldtouch Bluetooth 

Mouse once it has been detected, then click "Pair."
4.  When the Goldtouch Bluetooth Mouse shows "Connected," 

exit the screen and begin using your mouse.

Pairing the Goldtouch Comfort Mouse

Ensure the mouse is turned on and in pairing mode by pressing the 

recessed button on the bottom of the mouse

1.  From System Preferences, click the Bluetooth icon located in the 

Internet and Wireless Section
2.  Press the Pairing Button on the bottom of the Mouse for 2-3 

seconds, until the Red Sensor light it blinking to indicate pairing 

mode. Note: You may or may not see a blinking sensor depending 

on your lighting conditions. 

3.  Click the button labeled “Set Up New Device”.
4.  From the “Bluetooth Setup Assistant”, select the Goldtouch Com-

fort Mouse once it has been detected, then click “Continue”.
5.  Upon successful completion, the screen will display “Congratula-

tions, your computer is now setup to use your Bluetooth mouse”.
6. Click “Quit.

Windows 8

Mac OS X

Windows 10

Windows XP SP2, SP3

Pairing the Goldtouch Comfort Mouse

Ensure the mouse is turned on and in pairing mode by pressing the 

recessed button on the bottom of the mouse

1.  From the Start Menu, select “Devices and Printers", or right-click 

the Bluetooth icon on the task bar and select "Add a Bluetooth 

Device."
2.  Press the Pairing Button on the bottom of the Mouse for 2-3 

seconds until the Red Sensor light is blinking to indicate pairing 

mode. Note: You may or may not see a blinking sensor depending 

on your lighting conditions. 
3.  Click “Add a Device”.
4.  From the “Add a Device” window, select the Goldtouch Comfort 

Mouse once it has been detected, then click “Next”.
5.  Upon successful completion, the screen will display “This device 

has been successfully added to this computer."
6. Click "Close."

Windows 7

NOTE:

 

For all operating systems, if a security policy requires you to enter a Passkey, enter “0000”.

Pairing the Goldtouch Comfort Mouse

Ensure the mouse is turned on and in pairing mode by pressing the 

recessed button on the bottom of the mouse

Reviews: