Graco Hydra-Clean 308511J Instructions-Parts List Manual Download | Manualshive

Page: 1 / 10

background image

Hydra-Clean

R

Gun

For use in pressure washing applications with water and cleaning solutions only.

5000 psi (280 bar, 28.0 MPa) Maximum Working Pressure
Part No. 803350 Brass Body
Part No. 804589
Part No. 15T283

4500 psi (314 bar, 13.4 MPa) Maximum Working Pressure
Part No. 803351 Stainless Steel Body
Part No. 15T282

Instructions–Parts List

308511J

Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.

Model 803351 Shown

1
2
3
...
»

Summary of Contents for Hydra-Clean 308511J











Reviews:

No comments

Related manuals for Hydra-Clean 308511J

Brand: Campbell Hausfeld Pages: 1

Brand: YATO Pages: 80

PRO RDP-SGLG20 SOLO

Brand: Raider Pages: 46

Brand: Urrea Pages: 12

Brand: Campbell Hausfeld Pages: 32

Brand: Bostitch Pages: 32

Brand: Bostitch Pages: 32

Brand: Dajiang Innovation Technology Pages: 10

Brand: Makita Pages: 52

Brand: VonHaus Pages: 28

Brand: TJEP Pages: 180

TR 70 LCD Series

Brand: Reka Pages: 14

Brand: Reka Pages: 28

PAKARTE TR 50.4.25

Brand: Reka Pages: 28

Brand: Meec tools Pages: 24

Brand: Meec tools Pages: 44

Brand: Meec tools Pages: 68

Brand: GLW Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands