background image

 

Page 1 of 6 

 

 

          

 

 

GCRK  

Manual On/Off Remote Control with Timer for Millivolt Valve 

Installation and Operating Instructions 

 

IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS. DO NOT ATTEMPT TO INSTALL OR 

OPERATE

 

This Manual on/off   remote control with Timer transmitter is designed to be used with millivolt valve gas 

appliances. It can be operated   on/off from the transmitter or turned on and off manually from the receiver.

 

CONTENTS OF KIT 

 

Description 

Quantity 

Transmitter 

GCRK Timer remote control Transmitter 

 

 

Receiver Box 

Slide Button-Black  and White Color (On/RS/Off) 

Wall Cover Plate-Black and White Color 

Battery Door- Black and White Color 

Plug-In Wiring Assembly – 22” Inches 

 

Installation Instructions 

#6 3/4 Screws (for Wall Cover Plate and Remote control) 

#6 3/4 Screws (for fireplace system control covers) 

Plastic wall anchors (for installing transmitter)

 

 

NOTE: Due to the sensitive temperature monitoring components in the transmitter, it is necessary to allow the 

transmitter to stabilize to room temperature before accurate room temperature are displayed, If the transmitter is 

activated from a severe cold condition allow 15 minutes for accurate temperature reading to appear on the LCD. 

 

WARNING 

Important Safety Information 

 

Read this manual thoroughly prior to installing, programming or operating any remote control. 

 

This remote-control system is designed for use with a millivolt or 24V gas valve system.  Do not use 

this remote-control system on applications with voltages above 24 Volts AC/DC and 1 amp current. 

 

This remote-control system requires two (2) “AAA” and four (4) “AA” alkaline batteries to power the 

transmitter and receiver.   

 

Turn appliance OFF (at the appliance or remote receiver) if you are away from your house for a 

long period of time.  

 

FEATURES/SPECIFICATIONS 

 

 

Easy Operate Manual on/off and Timer Control 

 

Battery Powered Transmitter and Receiver 

 

Low battery Indication 

 

Select Between °C and °F display 

 

Child Proof Lock-out 

 

16 Security Codes 

 

Quick Disconnect Wiring Assembly 

 

Summary of Contents for GCRK







Reviews: