Greenheck PVF Installation And Operation Manual Download | Manualshive

Page: 1 / 32

background image

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
operate or maintain the product described. Protect yourself and others by observing all safety information. Failure
to comply with instructions could result in personal injury and/or property damage!

Indirect Gas-Fired Heat Modules

1

General Safety Information

These indirect gas-ﬁred furnaces are commonly used
in many different manufacturer’s ventilating products.
For unit-speciﬁc information, refer to the Installation,
Operation and Maintenance manual (IOM) for the unit in
which this furnace is installed.

•

Both the furnace units are listed for installation in the
United States and in Canada.

•

Installation of gas-ﬁred duct furnaces must conform
with local building codes. In the absence of local
building codes, installation must conform to the
National Fuel Gas code, ANSI Z223.1 or in Canada,
CAN/CGA-B149 Installation codes.

•

All electrical wiring must be in accordance with the
regulations of the National Electric Code, ANSI/
NFPA-70.

•

Unit is approved for installation downstream from
refrigeration units. In these conditions, condensate
could form in the duct furnace and provision must be
made to dispose of the condensate.

FOR YOUR SAFETY

If you smell gas:
1. Open windows.
2. Do not touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.

FOR YOUR SAFETY

The use and storage of gasoline or other
flammable vapors and liquids in open
containers in the vicinity of this appliance is
hazardous.

WARNING

Improper installation, adjustment, alteration,
service or maintenance can cause injury or
death. Read the installation, operating and
maintenance instructions thoroughly before
installing or servicing this equipment.

Recognized Component

®

®

Document 474645

Model PVF and PVG

Indirect Gas-Fired Heat Modules

Model PVF

Model PVG

1
2
3
...
»

Summary of Contents for PVF

































Reviews:

No comments

Related manuals for PVF

Brand: Suburban Pages: 8

Brand: York Pages: 8

Brand: Allied Air Pages: 41

SUPER JACK SJ125

Brand: Yukon Eagle Pages: 24

CARBOLITE GERO CWF 12/65

Brand: VERDER Pages: 36

Brand: Fluke Pages: 47

Brand: CAC / BDP Pages: 46

Brand: CAC / BDP Pages: 52

Brand: Cameo Pages: 36

Brand: York Pages: 4

Brand: Bard Pages: 73

Brand: Haier Pages: 51

Suburban SF Series

Brand: Airxcel Pages: 24

Brand: Thermo Scientific Pages: 70

Brand: Granby Pages: 33

Brand: Granby Pages: 35

Brand: Granby Pages: 36

Brand: Granby Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands