GR300
GR300
GR300
GR300-
-
-
-400
400
400
400-
-
-
-600
600
600
600
MOTOR
MOTOR
MOTOR
MOTOR
FOR SWING GATES
FOR SWING GATES
FOR SWING GATES
FOR SWING GATES
INSTALLATION MANUAL
Our compliments for your excellent choice. The GR300-400-600 electro-mechanical gear motor has been produced for
reliability and high quality. This Manual will offer information you may need to install your gear motor assuring long-lasting
performance and to safeguard your safety.
HOWEVER CAUTION IS UNQUESTIONABLY INDISPENSABLE AND NOTHING IS BETTER THAN PREVENTING ACCIDENTS. GR
products have been made to conform with rules and laws in force at time of manufacture.
This manual is designed exclusively for the specialized installation expert in the criteria of construction and equipment
to assist in the protection against accidents in the installation and use of the gate; door and automation of such gates (adhere
to the rules and laws in force).
On completion the installer should issue to the end consumer an instruction manual according to EN 12635.
Before proceeding with the installation the installer must provide an analysis of the identification and management of
risks as per the standards EN 12453 and EN 12445.
All wiring of the various external electrical components connected to the automation (e.g. Photocells, flashing lights,
keypads etc) must be carried out according to EN 60204-1 and the amendments made of the point 5.2.2 of EN 12453.
It is prohibited to do any repair or adjustment of the equipment if you have not taken all necessary precautions to avoid
possible accidents (example: power supply disconnected, engine block). All mechanisms in motion must be equipped with
appropriate protections.
The mains power line must be protected for maximum current in locked rotor condition as per government electrical
laws.
Install the gear motor on gates that conform to EN 12604.
Perform the measure of strength developed by the gear motor and take the appropriate steps as per EN 12445.
Positioning photocells: These safety devices must be installed at a height not exceeding 70cm from the ground and at a
distance from the floor movement of the door of no more than 20cm. Their proper functioning of the photocells must be
verified at the end of installation according to Section 7.2.1 of EN12445.
Keep the activation controls of automation out of reach of children. The controls should be installed at a minimum 1.5m
height above the ground and outside the range of actions of moving parts such as the gate.
All activation actions must be executed only at points from where the automation is fully visible.
Operate the remote only in view of automation.
Store carefully this manual in a suitable place known to all interested people.
Any unauthorized and arbitrary modification made to this product, releases the company GR Sistemi Automatici di apertura
Srl and from any liability resulting from damage or injury to things, people or animals.
The non-observance of regulations and of safety standards here listed releases the company GR Sistemi Automatici di
apertura Srl from any liability resulting from damage or injury to things, people or animals.
The automation must be coupled to a control board equipped with torque regulation that provides an anti crushing safety as
described in EN 12453 - EN 12445
This product falls within the scope of the Directive 2012/19 / EU concerning the management of waste electrical and electronic
equipment (WEEE). The appliance must not be disposed of with domestic waste as it is made of different materials that can be
recycled at the appropriate facilities. Inquire through the municipal authority regarding the location of the ecological platforms
to receive the product for disposal and its subsequent correct recycling. Furthermore, it should be remembered that, upon
purchase of an equivalent appliance, the distributor is obliged to collect the product for disposal free of charge. The product is
not potentially dangerous for human health and the environment, not containing harmful substances, but if abandoned in the
environment negatively impacts on the ecosystem. Read the instructions carefully before using the appliance for the first
time. It is recommended that you do not use the product for any purpose other than that for which it was intended, there
being a danger of electric shock if used improperly.
The crossed-out bin symbol, on the label on the appliance, indicates the compliance of this product
with the regulations regarding waste electrical and electronic equipment. Abandonment in the
environment of the equipment or illegal disposal of the equipment is punishable by law.
GRITAL GROUP AUTOMATIC SYSTEMS
IO29/E – rev. 01
