GSL electronics MPPT12-2P Operating Instructions Manual Download

Page: 1 / 8

MPPT12-2P R7

Page 1 of 8

Model:

MPPT12-2P

Unit 2, 110 Station Road, Seven Hills ,NSW, 2147, Australia

400W Solar Charger

Maximum Power Point Tracker

Operating Instructions

Please read these instructions before use

This revolutionary maximum power point tracker solar charger

was designed using the technology that won GSL Electronics the

prestigious “2008 EDN Innovation award”. A simple, compact and

low cost alternative. Ideal for charging batteries with the new low

cost high efficiency grid type panels.

MPPT12-2P Unit

MPPT12-2P Specifications

Efficiency Typical

96%

Input Voltage

16V to 55V

Output Voltage (Float)

13.5V / 27V

Output Voltage (Bulk)

Flooded 14.5V / 29V, Sealed 14.2V / 28.4V

Maximum Panel Power

400W @ 24V Charging / 200W @ 12V Charging

Quiescent Current

0.04A

Thermal Protection

Internal 85°C Protection Limit

Dimensions (mm)

35 X 75 X 126mm

Indications

Remote LED LVD Alarm

PATENT APPLIED FOR - 2010901565

Summary of Contents for MPPT12-2P









Search results

Summary of Contents for MPPT12-2P

Reviews:

Related manuals for MPPT12-2P

Brands by name

Popular brands

GSL electronics MPPT12-2P, Operating Instructions Manual

Search results

Summary of Contents for MPPT12-2P

Reviews:

Related manuals for MPPT12-2P

Brands by name

Popular brands