background image

 

 

4600 Series Narrow Stile Trim  

 

 

Installation Instructions 

 

 

 

I-ED01164 

Rev 3, Rev Date: 8/4/2017 

27390048 

 Page 1 of 

 

Hager Companies  139 Victor Street, St. Louis, MO 63104   (800) 325-9995   www.hagerco.com 

 

 

 

 

 

OVERVIEW 

                

 

 

 

 

46CE 
Cylinder Escutcheon 

Key Locks & Unlocks Levers 
Requires a mortise cylinder (3902) 

and “L” Cam (3976) 
with radius 0.637” (16mm).  Both 

sold separately.

 

46NK 
Night Lever 

Lever Operable When Key Is Turned.  Key Removable Only 
When Locked 

Requires a mortise cylinder (3902) and “L” Cam (3976) 
with radius 0.637” (16mm).  Both sold separately.

 

 

 

46BE 

Blank Escutcheon 
Always Operable

 

46DT 

Dummy 
Pull When Exit Device Is Dogged 

 

 

 

46NL 

Night Latch 
Key Retracts Latchbolt 
Requires a RIM cylinder (3901) and 

extra long  
tailpiece (2-639-7058).   

Both sold separately.

 

 

 

 

Handing Pin 

Mounting Post 

(2 places) 

Cylinder Cam 

Cylinder Nut 

Adjustable 
Tailpiece 

DEVICES COVERED IN THIS DOCUMENT: 

 

46CE Cylinder Escutcheon – Key locks and  
unlocks lever 

 

46DT Dummy Trim – Pull when dogged 

 

46BE Blank Escutcheon – Always operable 

 

46NL Night Latch – Key retracts latchbolt 

 

46NK Night Lever (09 Function) – Lever operable 
when key is turned.  Key removable only when 

locked. 

 

 

Cylinder Collar 

Mortise Cylinder 

Lever Handle 

(46CE Cylinder 
Escutcheon Shown) 

Summary of Contents for 46CE






Reviews: