1
2
ES10V-E1(H)
ES15V-E1(H)
ES25V-E1(H)
Haier Home Water Heater
Instruction manual
0040503116
V
OFF
MAX
Temp
Heating
Please read this Instruction Manual carefully before use.
Please retain this manual for future reference.
Troubleshooting
Specifications
Front View
Side View
Cut View
Back View
a
b
G
B
A
c
d
e
H
F
D E
c
Introduction of exterior and accessories
Technical parameters
Electrical Diagram
Model
a
b
c
d
e
ES10V-E1 (H) 300mm
338mm
456mm
152mm
100mm
ES15V-E1 (H) 335mm
374mm
495mm
152mm
100mm
ES25V-E1 (H) 370mm
409mm
546mm
152mm
100mm
Note:
1. The margin of error for the above parameters (measurements, weight) is ±10%.
2. Water temperature indicator is not a precision thermometer. It consists of three areas
denoted by blue; orange and red, which indicate the temperature of water in the
inner chamber from low to high respectively.
(Fig.2)
Remarks:
The permitted error limit of net weight above is
±
10%.
Item
Unit ES10V-E1 (H)
ES15V-E1 (H)
ES25V-E1 (H)
Rated voltage
V
230
230
230
Rated frequency
Hz
50
50
50
Rated pressure
MPa
0.80
0.80
0.80
Power
W
2000
2000
2000
Net weight
kg
Rated temperature
o
C
75
75
75
Volume
L
10
15
25
Waterproof grade
/
IPX4
IPX4
IPX4
Mixing factor
%
Tap water pressure
MPa No less than 0.05MPaNo less than 0.05MPaNo less than 0.05MPa
Average temperature of hot water outlet
o
C
Re-heating time
(a temperature rise of 50
o
C)
min
Diameter of power wire
mm
2
3×1.5
3×1.5
3×1.5
E
BT
MT
L
N
EH
E
HL
L : Brown wire
N : Blue wire
MT : High temperature limiter
BT : Thermostat
HL : Heating indicator
EH : Heating element
E : Yellow/green wire
Symptom
Things to Check
Solutions
No water
1
Whether the water supply
has stopped or whether the
water pressure is too low
Check
2
Whether the water-
usage point is blocked or
whether the hot water
valve is opened
Check and clear
Only cold
water but
the heating
indicator light
is lit
1
Whether hot water outlet
is opened
Check and open
2
Whether the water
temperature is adjusted
Increase the temperature to the required
value. Once the water is heated to the pre-set
temperature, control flow volume of cold and
hot water using the moderating mixing valve.
3
Heating time is too short
and set temperature is
not achieved
Continue heating
4
Whether heating pipe is
damaged
Confirm this is not due to the reasons
123
,
then contact Maintenance Department
Only cold water
and the heating
indicator light
is not lit
1
Whether power is
properly connected
Check power socket
2
Whether thermostat is
out of control
Confirm this is not due to the reasons
1
,
then contact Maintenance Department
Heating
indicator light
is on all the time
1
Water has not reached
the set temperature
Continue heating
2
Whether thermostat is
out of control
Confirm this is not due to the reasons
1
,
then contact Maintenance Department
Water volume is
sometimes large
or small, or water
is sometimes hot
or cold
Whether water pressure is
stable
Set lower mixing valve or ensure water
pressure is stable before use
Small hot water
outlet volume
1
Whether the present
temperature setting is
too low
Calibrate using the method stipulated in the
Instruction Manual
2
Whether water pressure is
excessive
Set lower mixing valve
Safety Notices
(Please read before use)
Prohibited
Compulsory
Matters
Essential Matters
our Service Center once the water heater does
not work properly or emits burnt smell.
230V/50Hz independent power source
must be used at all times.
To ensure safety, the water heater should
be connected to independent sockets (do
not use adapters), with reliable earthing. In
addition the power socket must conform
to national standards. Use of water heater
without reliable earthing is strictly prohibited.
Use pen multimeter to check whether the live
line and neutral line are reverse.
Do not use damaged wire and power
socket. Promptly clean the dust on the
power plug and socket.
Check the power meter and the electric
wire's diameter to ensure that they comply
with the rated current for the water
electrician to check the electric circuit.
near the water heater is strictly prohibited.
Do not touch the plug with wet hands,
and make sure that the water heater, plug
socket do not come into contact with
water. If they are accidentally wet, they
must be checked by professional persons
appointed by our company before using,
in order to prevent electrocution.
Do not connect to power when installing
or repairing the water heater.
Non-professionals are strictly prohibited
from carrying out repairs, maintenance,
dismantling or revamping of the water
heater.
Installation of water heater outdoors is
strictly prohibited.
Do not install the water heater in an environment
which is susceptible to ice-formation. Ice will
cause the container and water pipe to break,
leading to scalding and water leakage.
Please take precautionary measures
during cold weather, in order to prevent
damage to water heater from freezing.
If the soft power cable is damaged, it
from the manufacturers or Maintenance
Department in order to avoid danger.
Take care not to be scalded by heated water.
· Touching of hot water valve and pipes is
strictly prohibited.
· Make sure to check the water temperature
before use, use only when it feels comfortable.
Do not use water from the water heater
for drinking or similar purposes.
water heater was not used for an extended
period of time. Drain the water heater of
all water according to the instructions in
the chapter on Cleaning and Maintenance.
A: Water inlet pipe
B: Water outlet pipe
C: Inner chamber
D: Heater
E: Magnesium rod
F: Temperature
measurement pipe
G: Wall-mount support
H: Washer
Meanings of Icons
Earthing
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Forbidden
Warning
Warning
Warning
Warning
Warning
Warning
Caution
Caution
Caution
Forbidden
ＣＳＨ１０Ｄ００３８＿ＥＮ．ｉｎｄｄ １
５／２５／２０１０ ４：２７：１５ ＰＭ
2.7
0.9
3.0
69
69
64
8
11
14
20
25
45
