background image

13 SEER      2  3  4  5 Ton

 Installation & Operation Manual

 Air Handler

G

WARNING

WHEN THIS APPLIANCE IS INSTALLED IN AN ENCLOSED AREA, SUCH AS

A GARAGE OR UTILITY ROOM, WITH ANY CARBON MONOXIDE PRODUCING

DEVICES (i.e. AUTOMOBILE, SPACE HEATER, WATER HEATER,ETC.) INSURE

THAT THE ENCLOSED AREA IS PROPERLY VENTILATED.

WARNING

CARBON MONOXIDE (REFERED TO AS CO) CAN CAUSE PERSONAL INJURY

OR DEATH

WARNING

FAILURE TO FOLLOW THESE INSTRUCTIONS, LOCAL CODES OR NATIONAL

CODES MAY CAUSE FIRE, EXPLOSION, ELECTRICAL SHOCK, PERSONAL

INJURY OR PROPERTY DAMAGE.

FOLLOW ALL LOCAL CODES. IN THE ABSENCE OF LOCAL CODES REFER TO :
                                  

   NATIONAL ELECTRICAL CODE NFPA 70

                                     NFPA 90A & 90B
                                     UNIFORM MECHANICAL CODE

READ THESE INSTRUCTIONS COMPLETELY BEFORE ATTEMPTING TO INSTALL
OR SERVICE THIS APPLIANCE.

ONLY FACTORY AUTHORIZED KITS OR ACCESSORIES SHOULD BE USED WHEN
INSTALLING OR MODIFYING THIS APPLIANCE, UNLESS OTHERWISE NOTED IN
THESE INSTRUCTIONS.

SOME LOCALITIES MAY REQUIRE THE INSTALLER/SERVICER TO BE LICENSED.
IF IN DOUBT CONTACT YOUR LOCAL AUTHORITIES.

These instructions should be retained and kept adjacent to the unit for future reference.

MODEL #  HB                M20      HB

MODEL #  HB                V20       HB

INSTALLATION DATE

The information contained in this booklet is subject to change without notice.

No.  0010572323

M22

V22

Summary of Contents for HB2400VD2M20

















Reviews: