background image

HQ Little Foot Frame Assembly Instructions 

 | 1

December, 2019

HQ Little Foot

 Frame

Assembly Instructions

Table of Contents

Frame Parts and Hardware     2

Table and Leg Assembly 

   4

Side Arm and Pole Assembly     7

Introduction

The HQ Little Foot frame can be set up to work with either the HQ Simply Sixteen™ (a 16-inch quilting 

machine) or the HQ Avanté® an 18-inch quilting machine). The frame enables you to use either stand-up 

quilting machine within a smaller footprint than the HQ Studio Frame, yet you can do quilts of any size.

 

ONLINE

: For more information about setting up the HQ Little Foot frame, watch the video 

Setting 

Up the HQ Little Foot frame 

at: 

http://www.handiquilter.com/videos/HQLittleFoot100

.  

What’s Included

Your HQ Little Foot Frame is delivered in two separate boxes. After opening, check immediately to see that 

you have received the items listed in the Parts and Hardware list found on pages 2 and 3.

Box 1:

Includes side arms and supports, upper leg supports, HQ Little Foot frame assembly instructions, and all 

other parts and hardware. 

Box 2:

1 – Table top with tracks

2 – Lower legs 

1 – Front pole (56”)

1 – Rear pole (68”)

NOTES:

1.

REVISIONS

ECO

REV.

DESCRIPTION

DATE

APPROVED

A

INITIAL RELEASE

BILL OF MATERIALS ENG-10007

ITEM PART NUMBER

DESCRIPTION

QTY.

1 QF05300-300

TABLE ASSY, TACONY FRAME

1

2 QF05300-402

CORNER HEIGHT BAR, A

2

3 QF05300-403

CORNER HEIGHT BAR, B

2

4 QF05300-401

END LEG STAND

2

5 QF09318-303

SCREW-M6x12 SWH

6

6 QF09318-07

Screw-M8x16 SBHCS

16

7 QF09318-108

LEVELING GLIDE

4

8 ENG-10005

ASSY-SIDE ARM RIGHT LF

1

9 ENG-10006

ASSY-SIDE ARM LEFT LF

1

10 QF10005

POLE FRONT LF

1

11 QF10009

POLE REAR LF

1

12 QF10011

END CAP-REAR POLE LF

2

ENG-10007

D

C

B

A

A

B

C

D

1

2

3

4

5

6

7

8

8

7

6

5

4

3

2

1

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

Handi Quilter.  ANY REPRODUCTION IN

PART OR AS A WHOLE WITHOUT THE 

WRITTEN PERMISSION OF

Handi Quilter IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

NEXT ASSY

USED ON

APPLICATION

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

ANGULAR: MACH  1     BEND 

TWO PLACE DECIMAL     0.01

THREE PLACE DECIMAL    0.005

INTERPRET GEOMETRIC

TOLERANCING PER:

MATERIAL

FINISH

DRAWN

CHECKED

ENG APPR.

MFG APPR.

Q.A.

DATE

NAME

Handi Quilter

SIZE

B

DWG.  NO

REV

SHEET 1 OF 1

WEIGHT:

SCALE: 1:16

UNLESS OTHERWISE SPECIFIED:

A

 LBS

Sheet Name: Sheet1

Filename

FRAME-LITTLE FOOT

Handi Quilter, Inc.

501 North 400 West

North Salt Lake, UT 84054

1-877-697-8458

© 2015 Handi Quilter, Inc.

www.HandiQuilter.com

Printed in the United States

December 10, 2019

Part # QF31001

Back of

Frame

Front of

Frame

Summary of Contents for HQ Little Foot Frame














Reviews: