background image

 

Hanover

 

Outdoor

 

Furniture

 

 

 

 

 

IMPORTANT

 

If

 

you

 

have

 

any

 

problems

 

with

 

this

 

product

 

(missing

 

or

 

damaged

 

parts,

 

assembly

 

issues,

 

etc.),

 

PLEASE

 

DO

 

NOT

 

RETURN

 

TO

 

THE

 

RETAILER/STORE

   

from

 

where

 

you

 

purchased

 

the

 

product.

     

Please

 

call

 

our

 

Toll

Free

 

Customer

 

Service

 

Hotline

 

at:

 

1

800

416

3511

 

Between

 

9:00

 

AM

 

and

 

5:00

 

PM

 

Eastern

 

Time,

 

Monday

 

through

 

Friday

 

Or

 

visit

 

our

 

website

 

at:

   

www.hanover

products.com

 

 

 

To

 

expedite

 

any

 

future

 

warranty

 

claims,

 

please

 

retain

 

the

 

Instruction

 

Sheet,

 

Warranty

 

Card

 

and

 

receipt

 

for

 

future

 

use.

 

 

For

 

additional

 

on

line

 

support

 

on

 

assembly,

 

troubleshooting

 

and

 

care

 

&

 

maintenance

 

of

 

your

 

outdoor

 

furniture,

 

please

 

visit

 

our

 

website

 

at:

   

www.hanover

products.com

.

 

 

6/1/2015

 

(a)

 

Summary of Contents for ORL4PCSQFPGRN





















Reviews: