background image

Harman®  •  PF-120 Owner’s Manual_R3  •  2014 -___  •  10/14

1

3-90-08120c

Please read this entire manual before 

installation and use of this pellet fuel-

burning room heater. 

Failure to follow these instructions could 

result in property damage, bodily injury 

or even death.

•   Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

•   Do not overfire - If any external part starts to glow, you 

are overfiring. Reduce feed rate. Overfiring will void 

your warranty.

•   Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

Check building codes prior to installation.
•   Installation  MUST  comply  with  local,  regional,  state 

and national codes and regulations.

•   Contact local building or fire officials about restrictions 

and installation inspection requirements in your area.

Tested  and  approved  for  wood  pellets.  Burning  of  any 

other type of fuel voids your warranty.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as 

stove.

•  Alert children and adults to hazards of high temperatures.

  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other flammable 

materials away.

HOT SURFACES!

Glass and other surfaces are hot during 

operation and cool down.

NOTE

To  obtain  a  French  translation  of  this  manual,  please 

contact your dealer or visit www.harmanstoves.com
Pour obtenir une traduction française de ce manuel, s’il 

vous  plaît  contacter  votre  revendeur  ou  visitez  www.

harmanstoves.com

Model(s):

PF-120 Pellet Furnace

NOTICE: SAVE THESE INSTRUCTIONS

CAUTION

!

CAUTION

!

WARNING

!

WARNING

!

Owner’s Manual

Care and Operation

INSTALLER: Leave this manual with party responsible for use and operation.

OwNER: Retain this manual for future reference.

Call your dealer for questions on Installation, Operation, or Service.

Summary of Contents for PF-120



































Reviews: