background image

Inside Style Lift 

AL200 / AL400  / AL055 

Installation Guide & Owners Manual 

 

 
 

 
 
 
 
 
 
 
 
 
 
 

AL200 Manual Rotation Lift          AL400 Fully Powered  Lift            AL055 Economy Lift 
 

 
 

Congratulations on your new lift purchase.  The Universal Inside Lift line is one of the easiest and most trouble free 
ways to transport your scooter or power chair.  This manual is written to be used both as an installation guide as well 
as an operation guide for the end user.  Please read the manual thoroughly BEFORE attempting any installation, ad-
justment or use of the lift. 
 
Both installers and operators should familiarize themselves with this entire manual. 
 
The manual will be divided into the following sections for easy reference; 

 

                  Section 1  - Unpacking the Lift 
                  Section 2  - Vehicle Preparation 
                  Section 3  - Wiring the Vehicle 
                  Section 4  - AL200 Installation & Operation 
                  Section 5  - AL400 Installation & Operation 
                  Section 6 -  AL055 Installation & Operation 
                  Section 7  - Safety & Maintenance 

 
If you have any questions or comments concerning the installation or operation of your scooter lift, please contact 
your local distributor for additional technical information.  Only authorized dealers should install this lift. 
 
 
 

Caution: 

Some scooters and power chairs may be unsuitable for transport in or on a motor  

vehicle.  Please contact the manufacturer of your mobility device to determine its transportability

.  

 

Summary of Contents for AL055

























Reviews: