Haws 1210S Installation, Operation & Maintenance Instructions Manual Download

Page: 1 / 17

01/21 1210 Series Bottle Fillers

Page 1 of 17

1455 Kleppe Lane



Sparks, NV 89431-6467



(775) 359-4712



Fax (775) 359-7424

E-mail:

haws@hawsco.com



website:

www.hawsco.com

No. 0510001059 (1)

Bottle Filling Stations

MODELS 1210S AND 1210SF

INSTALLATION, OPERATION

MAINTENANCE INSTRUCTIONS

SAFETY PRECAUTIONS

CAUTION: Disconnect electrical power to outlet before installing or servicing.

NOTICE:

A. The electrical receptacle must have code-approved ground-fault circuit

interrupter (GFCI) protection for personnel.

B. Care should be taken not to damage refrigeration system lines or

electrical wires during installation.

C. Installation must conform to all applicable codes and standards.
D. Maintain 8 inches (20cm) separation from filter circuit board (antenna) at

all times.

NOTE TO INSTALLER: Please leave this information with the Maintenance Department.

FULL-SCALE ROUGH-IN TEMPLATE (PN 0510001160) AVAILABLE UPON REQUEST.

SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:

TECHNICAL SUPPORT:

1-800-766-5612

FOR CUSTOMER SERVICE:

1-888-640-4297

Summary of Contents for 1210S


















Search results

Summary of Contents for 1210S

Reviews:

Related manuals for 1210S

Brands by name

Popular brands

Haws 1210S, Installation, Operation & Maintenance Instructions Manual

Search results

Summary of Contents for 1210S

Reviews:

Related manuals for 1210S

Brands by name

Popular brands