background image

P/N: IS3220VSC 

Rev:  B

 

__________________________________________________________________________________________ 

OWNER’S MANUAL

 

INSTALLATION, OPERATION, & PARTS

 

TriStar Energy Solution 

TM 

Variable Speed Pump Control

 

The Hayward TriStar Pump is specifically engineered for the demanding requirements of today’s in­ground swimming pool/spa that is 
equipped with large capacity filters, heaters, and pool cleaning equipment.  The TriStar is a self­priming pump that includes an 
improved seal and impeller design that will provide many years of efficient, dependable, corrosion­free service.  The advanced design 
provides superior performance while reducing maintenance requirements.

  NOTE ­

To prevent potential injury and to avoid 

unnecessary service calls, read this manual carefully and completely.

 

WARNING 

– 

The TriStar ES (Energy Solution) variable speed pump control is designed for use only with 

Hayward SP322063EEV 2.7 THP 3 phase pump.

  Do not use with any other pump models.  Use of this control with any other pump 

model will void warranty.  Refer to TriStar Owner’s Guide (IS3200) for all applicable pump installation, operation, and 
troubleshooting information.

 

SAVE THIS INSTRUCTION MANUAL 

HAYWARD POOL PRODUCTS 

620 DIVISION STREET    ELIZABETH, NJ  07207    (908) 351­5400 

WWW.HAYWARDPOOL.COM

Summary of Contents for TriStar SP322063EEV

















Reviews: