background image

Heatit Controls AB can not be held liable for typographical errors, other errors or 
omittances in our information. Product specifications may change without further notice. 
All electrical installations must be carried out by a licensed electrician. The product must 
be installed in accordance with national building codes and our installers manual.

Heatit Controls AB   l   Läkarvägen 4, 454 31 BRASTAD, SWEDEN 
Phone: +47 61 18 77 77    l   post@heatit.com – 

www.heatit.com

INTRODUCTION

The Heatit Z-Push Wall Controller is a wireless wall mounted Z-Wave 
Controller. It has mounting options for 1, 2 or 3 rockers, allowing for easy 
and practical management of your Z-Wave products. The switch can 
be set up to control scenarios or work in association with other Z-Wave 
products. Each rocker switch has a dual color LED to indicate button 
actions. The Heatit Z-Push Wall Controller is supplied with all three sets 
of rockers in the box. The switch fits into System 55 frames.

STATEMENT REGARDING PRODUCTS FROM MULTIPLE 
MANUFACTURERS
Please read this before installation

This device may be used with all devices certified with the Z-Wave Plus™ 
certificate and should be compatible with such devices produced by 
any manufacturer. Every primary controller is different depending on 
the manufacturer, their target audience and intended use/application. 
Please review the functionalities implemented by the primary controller 
you intend to use with our Z-Wave Plus certified device to ensure that it 
provides the necessary controls to take full advantage of our product’s 
capabilities.

INSTALLATION

Installation must be done by a qualified electrician in accordance with 
national building codes. Before installation, disconnect the power to the 
device from the mains. During installation of the device, power to the 
device must be disconnected AT ALL TIMES!

1. 

Choose and mount the front, which covers your needs (for more 
information, see chapter ”Choosing the correct front/assembly” 
described in the complete manual).

2. 

Gently pull the battery plastic tag to power the product.

3. 

Start the adding procedure from your primary controller.

4. 

Press any UP button 6 times in a rapid sequence on the device (the 
device has a label on the battery cover, pointing towards the UP 
buttons). Your device is now added in your primary controller. 

5. 

Install the device in your preferred location.
a.  Fix the metal mounting bracket on the wall box or directly  

on the wall using the supplied screw kit.

b.  Place the device in the wall frame with arrows shown on  

label pointing upwards.

c.  Press the device and wall frame onto the metal mounting  

bracket.

Note: The rocker fastening clips may become looser after having been 
mounted and unmounted many times.

ADD/REMOVE

There are two ways to add your devices in a Z-Wave network:

Method 1: Standard (manual)

Please refer to your primary controller manual on how to set the 
primary controller in add/remove mode. The device can only be added 
or removed from the network if the primary controller is in add/remove 
mode.
1. 

Initiate the learning mode in the controller.

2. 

Press any UP button 6 times within 3 seconds. 

When the learning mode has  started, the LED corresponding to the 
button you pressed will blink green. The device will indicate ”Success” by 
emitting a green light for 3 seconds. 

Error while adding:
The learning mode times out after 30 seconds if the Heatit Z-Push Wall 
Controller does not receive any information from the gateway. 
The device will indicate ”Fail” by emitting a red light for 3 seconds, 
if this happens, please perform a removing process from the controller 
before restarting learning mode.

Method 2: SmartStart (Automatic)

Please refer to your primary controller/gateway to see if SmartStart 
is supported by the controller. SmartStart enabled products can be 

 TECHNICAL DATA

Protocol 

 

Z-Wave Plus, 868.4MHz

Chip 

 

Z-Wave 700 chip

Battery 

 

1 x CR2450 battery

Est. battery life 

 

Estimated 1 year (with default settings    

 

 

and max. 10 pushes per day)

Buttons 

 

1, 2 or 3 rockers 

Ambient temperature 

5°C to 40°C (0°C to 40°C storage)

Humidity 

 

Max 95% RH

Range RF 

 

Min. 40 meters 

IP Code 

 

IP 20

Size (LxWxH) 

 

55 x 55 x 14mm 

Approvals 

 

Z-Wave Plus V2 

 

 CE

 

 

RoHS 2002/95/EC

 

 

2002/96/EC (WEEE)

 

 

1999/5/EC (RTTE)

Read the full manual at: 

manuals.heatit.com

HEATIT Z-PUSH 

WALL CONTROLLER

Quick Guide

Ver 2021-A

added into a Z-Wave network by scanning the Z-Wave QR-Code found 
on the product with a controller providing SmartStart inclusion. No 
further action is required and the SmartStart product will be added 
automatically within 10 minutes of being switched on in the network 
vicinity.

If the device already belongs to a network, follow the removing process 
before adding it to your network. Otherwise, the adding of this device 
will fail. When the device is removed from the network, the device will 
revert to factory settings.

White RAL 9010

White RAL 9003

Black

Reviews: