HES K200-622 Installation Instructions Manual Download

Page: 1 / 12

Part Number 3085006.001, Rev. A

K200-622

Cabinet Lock Series

Installation Instructions

HES, Inc.
Phoenix, AZ
1.800.626.7590

www.hesinnovations.com

Machine

screw

with

washer

Package Contents

Strike Plate

‐

screws

5/16”

1”

1-5/8”

1-1/4”

1-3/4”

‐

1/2”

Shaft Extension

0-80x½”

2-56x3/8”

2-56x1-1/4”

Key Override

Paddle

6 x 1/2”

1-7/8”

Recommended Tools

Optional:

Cam Lock for key override

Double door bracket

Lock Body

Drill, Drill bits: 5/32”, 1/2”

Approved Credential:

i.e. iCLASS or Prox ID card

Flathead drivers 3/32”, 3/16”

Phillips drivers P0, P2

Pencil, Wire Stripper

Voltage:

12–24 VDC ±10% (Power Supply not provided)

Power Consumption:

<3W peak, 0.5W steady state

Operating Temperature:

-10C to 50C

Holding Force:

250 lbs

Lock Reader

Specifications

Mounting

Templates

Interface Cable, Lock Side

Interface Cable,

System Side

Summary of Contents for K200-622













Search results

Summary of Contents for K200-622

Reviews:

Related manuals for K200-622

Brands by name

Popular brands

HES K200-622, Installation Instructions Manual

Search results

Summary of Contents for K200-622

Reviews:

Related manuals for K200-622

Brands by name

Popular brands