background image

HOBO® Pendant® MX Temp (MX2201) and  
Temp/Light (MX2202) Logger Manual 

21536-L 

HOBO Pendant MX loggers measure temperature (MX2201) or temperature/light (MX2202) in 
indoor and outdoor environments. Designed for durability, these compact, waterproof loggers 
can be used in numerous applications, including fresh and salt water. The loggers are 
Bluetooth® Low Energy-enabled for wireless communication with a mobile device. Using the 
HOBOconnect™ app, you can easily configure the loggers, download logged data to your phone 
or tablet, or automatically upload the data to HOBOlink® for further analysis. You can also 
configure the loggers to calculate statistics, set up alarms to trip at specific thresholds, or 
enable burst logging in which data is logged at a faster interval when sensor readings are above 
or below certain limits. 

Specifications 

Temperature Sensor (MX2201 and MX2202) 

Range 

-20° to 70°C (-4° to 158°F) in air 
-20° to 50°C (-4° to 122°F) in water 

Accuracy 

±0.5°C from -20° to 70°C (-4° to 158°F) 

Resolution 

0.04°C (0.072°F) 

Drift 

<0.1°C (0.18°F) per year 

Response Time 

17 minutes typical to 90% in air moving 1 m/s, unmounted 
7 minutes typical to 90% in stirred water, unmounted 

Light Sensor (MX2202) 

Range 

0 to 167,731 lux (15,582 lum/ft

2

Accuracy 

±10% typical for direct sunlight (see 

Light Measurement

 on page 2 for 

more details) 

Logger 

 

Logger Operating Range 

-20° to 70°C (-4° to 158°F) in air 

Buoyancy (Fresh Water) 

2 g (0.07 oz) positive 

Waterproof 

To 30.5 m (100 ft) 

Radio Power 

1 mW (0 dBm) 

Transmission Range 

Approximately 30.5 m (100 ft) line-of-sight 

Wireless Data Standard 

Bluetooth Low Energy (Bluetooth Smart) 

Logging Rate 

1 second to 18 hours 

Time Accuracy 

±1 minute per month at 25°C (77°F) 

Battery 

CR2032 3V lithium, user replaceable 

Battery Life 

1 year typical at 25°C (77°F) with logging interval of 1 minute and 
Bluetooth Always On enabled in software. 
2 years typical at 25°C (77°F) with logging interval of 1 minute and 
Bluetooth Always On disabled in software. 
Faster logging intervals and statistics sampling intervals, burst logging, 
remaining connected with the app, excessive downloads, and paging 
may impact battery life. 
To ensure proper battery installation, see 

Battery Information

 for 

detailed instructions on replacing the battery. 

Memory 

96,000 measurements 

Full Memory Download 
Time 

Approximately 45 seconds; may take longer the farther the device is 
from the logger 

Wetted Materials 

Polypropylene case, EPDM O-ring 

Dimensions 

3.35 x 5.64 x 1.8 cm (1.32 x 2.22 x 0.69 inches) 

Weight 

12.75 g (0.45 oz) 

Environmental Rating 

IP68 

 

The CE Marking identifies this product as complying with all relevant 
directives in the European Union (EU). 

 

   

 

See last page 

HOBO Pendant MX 
Logger 

Models: 

 

MX Temp (MX2201) 

 

MX Temp/Light 
(MX2202) 

Required Items: 

 

HOBOconnect app 

 

Mobile device with 
Bluetooth and iOS, 
iPadOS®, or Android™ 

Accessories: 

 

Mounting boot 5-pack 
(BOOT-MX2201-2202) 

 

Solar radiation shield 
(RS1 or M-RSA) 

 

Mounting bracket for 
solar radiation shield 
(MX2200-RS-BRACKET) 

 

Replacement O-rings 
(MX2201-02-ORING) 

 

 

MX2201 Model Shown 

Summary of Contents for MX2201










Reviews: