1
2
3
4
5
Thank you for purchasing this product from HOLOSUN , the
TUBE HS406A1 is a monocular red dot sight. Please read the
User's Manual carefully before operation.
Features
Important notices
Battery
Installation
1.
Covert aiming:
When aiming, the red dot is projected within the
sight so no light can be detected by the target. Unlike a laser sight
that appears as a dot that can be seen on and by the target.
2.
Full field of view for target acquisition
: The user can gain rapid
target acquisition and situational awareness while aiming with
both eyes open.
3.
Low power consumption:
Only a few micro-amperes of current
are required for sight operation. Sight runs on one battery for up
to 30,000 hours. When battery replacement is required, the
battery compartment access through the battery tray.
4.
Motion power on:
The sensitive motion sensor will turn the power
on with any motion detection.
5.
Parallax free optical system:
Parallax is
≤±
1MOA.
1. Ensure that the firearm is completely unloaded and safe
before device installation, sighting in, installing a new
battery, or any other adjustment.
2. Always ensure that the muzzle of the firearm is pointed in a
safe direction when replacing the battery.
3. Please keep the packaging should you need to make a
warranty claim.
Fig2-2
1. The mounting bracket (Fig 3) is for attaching the sight to the
weapon. The sight comes with mounting bracket attached.
2. Attaching bracket to the sight:
1) Remove the 6 screws with the hex wrench and remove
the upper cover.
2) Mount the sight on the bracket and follow the orientation
and position which are shown in Fig 4.
3) Attach the upper cover and evenly tighten the 6 screws.
Use thread locker if available.
3. Mounting the bracket to the weapon:
1) The mounting bracket is adaptable to any firearm with a
Picatinny Rail. If the firearm has no Picatinny rail , or
Fig 3
Mount bracket
Upper cover
Screw
Clamp
socket
Cross bolt
Red Dot Sight
www.holosun.com
HS406A1
TUBE
User's Manual
7.
Brightness adjustment:
There are 12 settings(10 D2NV)
for the reticle as to match the ambient lighting conditions
8.
Memory function:
The sight will remember the last saved
brightness setting when powered on and off.
9.
Two top mounted buttons:
The top mounted buttons allow
for easy operation without obstructing the user's vision.
10.
Mounting bracket:
Compatible with Picatinny rail.
11.
Waterproof:
IP67
6.
Sleep time delay:
The sight will be automatically entered into
sleep mode after not being used for 8 hours.
LAYOUT
Fig1
Brightness
button
reduce
TUBE HS406A1
Protective cap
Brightness
button
increase
Battery compartment
Battery compartment
Battery
Screw 2
Screw 1
Slot
Screw 1
Screw 2
Battery
compart-
ment
O-ring
Battery compartment
Battery
Screw 2
Screw 1
O-ring
Fig2-1
1. The operating voltage for this device is DC3V using one
high quality CR2032 Lithium battery included with
purchase.
2. The high quality battery can power the device for up to
30,000 hours. Caution: The battery is not rechargeable.
3. Battery replacement
:
1) Removing the battery (Fig 2-1):
a) Loosen screws 1, 2.
b) Insert coin or similar
object in the battery
tray slot, pry out the
battery tray, and
remove the discharged
battery by lifting it up.
A tool is provided.
2) Battery installation (Fig2-2):
a) Insert the battery into
the battery tray by
pushing it down with
the correctly marked
polarities, "+" and "-"
.
b) Insert and press the
tray into the battery
compartment.
c) Tighten screws 1, 2.
Caution:
The loss or damage of O-ring will
cause water leaking into the battery
compartment and may damage
electronic circuits and the device.
