background image

 

HomeGrid Stack’d Series Installation Guide 

 

1.

 

Safety Precautions 

It is very important to read the user manual carefully before installing or using battery. Failure to 

do so or to follow any of the instructions or warnings in this document can result in electrical 

shock, serious injury, or death. Installing the battery incorrectly can permanently damage battery 

or rendering it inoperable. 
 

 

 

 

 

 

 

1.1.

 

General warnings 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Any internal lithium ion cell material such as electrolyte or powder on the skin or in the 

eyes must be flushed with plenty of clean water immediately. Then seek medical 

assistance. Any material spilled on clothing should be rinsed out with water. 

Explosion and fire hazard. Terminals of the Li-ion Battery are always alive; therefore, do not 

place items or tools on the Li-ion Battery. Avoid short circuits, over discharges and high 

charge currents. Use insulated tools. Do not wear any metallic items such as watches, 

bracelets, etc. In case of fire; you must use a type D, foam or CO2 fire extinguisher. 

Do not open or dismantle the battery. Electrolyte is very corrosive. In normal 

working conditions you will not have any contact with the electrolyte. If the battery 

casing is damaged do not touch the exposed electrolyte or powder because it is 

corrosive. 

 

For more information about this product, please visit the official website: 

http://www.homegridenergy.com

 

 

Work on a Li-ion Battery should be carried out by qualified personnel only. 

While working on the Li-ion Battery wear protective eyeglasses and clothing. 

Li-ion batteries are heavy. If involved in an  traffic accident they can become a 

projectile! Ensure adequate and secure mounting and always use suitable handling 

equipment for transportation. 

Handle with care because this lithium ion battery is sensitive to mechanical forces shock. 

Do not expose bare cables outs, all the battery terminals must be disconnected for 

 

Summary of Contents for Stack'd Series











Reviews: