background image

0-1

dummyhead

dummyhead

How to use this manual

How to use this manual

A Few Words About Safety

Service Information

The service and repair information contained in this manual is intended for use by qualified, professional technicians. Attempting

service or repairs without the proper training, tools, and equipment could cause injury to you and/or others. It could also damage

this Honda product or create an unsafe condition.
This manual describes the proper methods and procedures for performing service, maintenance, and repairs. Some procedures

require  the  use  special  tools.  Any  person  who  intends  to  use  a  replacement  part,  service  procedure,  or  a  tool  that  is  not

recommended by Honda must determine the risks to their personal safety and the safe operation of this product.
If you need to replace a part, use Honda Genuine parts with the correct part number or an equivalent part. We strongly recommend

that you do not use replacement parts of inferior quality.

For Your Customer’s Safety

Proper service and maintenance are essential to the customer’s  safety and the reliability of this product. Any error or oversight

while servicing this product can result in faulty operation, damage to the product, or injury to others.

For Your Safety

Because this manual is intended for the professional service technician, we do not provide warnings about many basic shop safety

practices (e.g., Hot parts-wear gloves). If you have not received shop safety training or do not feel confident about your knowledge

of safe servicing practices, we recommend that you do not attempt to perform the procedures described in this manual.
Some  of  the  most  important  general  service  safety  precautions  are  given  below.  However,  we  cannot  warn  you  of  every

conceivable hazard that can arise in performing service and repair procedures. Only you can decide whether or not you should

perform a given task.

Important Safety Precautions

Make sure you have a clear understanding of all basic shop safety practices and that you are wearing appropriate clothing and

using safety equipment. When performing any service task, be especially careful of the following:
 • Read all of the instructions before you begin, and make sure you have the tools, the replacement or repair parts, and the skills

required to perform the tasks safely and completely.

 • Protect your eyes by using proper safety glasses, goggles, or face shields anytime you hammer, drill, grind, or work around

pressurized air, pressurized liquids, springs or other stored-energy components. If there is any doubt, put on eye protection.

 • Use other protective wear when necessary, for example gloves or safety shoes. Handling hot or sharp parts can cause severe

burns or cuts. Before you grab something that looks like it can hurt you, stop and put on gloves.

 • Protect yourself and others whenever you have the product up in the air. Anytime you lift this product with a hoist, make sure

that the hoist hook is securely attached to the product.

Make sure the motor is off and the battery pack is removed before you begin any servicing procedures, unless the instruction tells

you to do otherwise. This will help eliminate several potential hazards:
 • Injury from moving parts. If the instruction tells you to run the motor, be sure your hands, fingers, and clothing are out of the way.

 • Do not tilt this product when starting the motor. Start the motor and run it on a flat surface that is free of obstacles.
Moisture and electricity are not compatible.
 • Always handle and connect battery pack in dry conditions.

 • Never allow battery pack to contact wet areas.
Keep all cigarettes, sparks, and flames away from the battery pack and its related equipment.

Improper service or repairs can create an unsafe 

condition that can cause your customer or others to 

be seriously hurt or killed.

Follow the procedures and precautions in this 

manual and other service materials carefully.

Failure to properly follow instructions and 

precautions can cause you to be seriously hurt or 

killed.

Follow the procedures and precautions in this 

manual carefully.

Summary of Contents for GXE2.0S




























































Reviews: