background image

ROME Series

Relay Option Module Enclosure

Product Installation Document

PN 53530:B   9/14/2009   09-327

The ROME (Relay Option Module Enclosure, red) and ROME-B (black) is shipped with one ANN-BUS Relay Module 
already installed.  The ROME Series provides mounting space for one additional Relay Module or one addressable Multi-
Module.  

Relay Module 

The Relay Module provides 10 programmable Form-C relays when used with a compatible FACP (Fire Alarm Control 
Panel).  This document is provided as a quick reference.  For more detailed programming information, refer to the appro-
priate FACP installation manual.

Relay Module Specifications

Relay Designations and Terminals

The relay numbers and terminal designations are illustrated in the following illustration.

Operating Voltage

24 VDC

Max. Current @ 
24 VDC

Alarm

75 mA

Standby

15 mA

Operating Temperature

32° to 120° F
(0° to 49° C)

Max. Wiring Distance from FACP
(with 12 AWG wire)

1,250 ft. (380 m)

Relay Contact Ratings

2 amps @ 30 VDC 
(resistive)

0.5 amps @ 30 VAC 
(resistive)

Indoor Use in Dry Location Only

Relay Module

Relay Module

Normally Open, 
Normally Closed 
and Common 
terminals for each 
relay follow the 
same pattern as 
illustrated above.

R9             R10

R7             R8

R5             R6

R3             R4

R1             R2

NO
NC
C

NO
NC
C

Summary of Contents for Fire-lite ROME Series







Reviews: