HAN101
Sealing Iron
Instruction Manual
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of
Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab
for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm
when operating this product:
NOTICE:
Procedures, which if not properly followed, create a possibility of physical property damage AND a
little or no possibility of injury.
CAUTION:
Procedures, which if not properly followed, create the probability of physical property damage
AND a possibility of serious injury.
WARNING:
Procedures, which if not properly followed, create the probability of property damage, collateral
damage, and serious injury OR create a high probability of superfi cial injury.
SPECIFICATIONS
Input voltage
110–120V, 60Hz
Current Draw
1.4A
Max. Temp.
469°F (243°C)
SETTING
TEMPERATURE
Low
115°F (46°C) ±27°F (15°C)
1
172°F (78°C) ±27°F (15°C)
2
234°F (112°C) ±27°F (15°C)
3
280°F (138°C) ±27°F (15°C)
4
327°F (164°C) ±27°F (15°C)
5
387°F (197°C) ±27°F (15°C)
Hi
442°F (228°C) ±27°F (15°C)
Thank you for purchasing the Hangar 9
®
Heat Sealing iron. It features a thermostatically controlled temperature
maintenance system that actually monitors the heat and regulates power to maintain the temperature settings
on the dial.
IMPORTANT
: Consult the instructions provided with the covering for suggested iron temperature settings.
Always start with a lower setting than recommended and increase the heat slowly if necessary.
The heat sealing iron also features a non-stick coated ironing surface that allows the iron to glide over the
covering material without scratching. This coating may produce a light smoke the fi rst time the covering iron
is used.
The specifi cally designed tip allows easy iron access between control surfaces and in hard-to-reach areas. A
convenient aluminum stand is also included.
WARNING:
Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product,
personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires
some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not intended for use by children without
direct adult supervision. Do not attempt disassembly, use with incompatible components or alter product in
any way without the approval of Horizon Hobby, LLC. This manual contains instructions for safety, operation
and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to
assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
LIMITED WARRANTY
What this Warranty Covers
- Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product
purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered
- This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage
due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation,
operation or maintenance, (iii) modifi cation of or to any part of the Product, (iv) attempted service by anyone
other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon
dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable
laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE
PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
- Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that
Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective.
Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement
decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims.
SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND
EXCLUSIVE REMEDY.
CAUTION
: Iron surface will become hot. Operating temperature can exceed 200°C (400°F). Use
extreme caution when operating this product to avoid burns.
