background image

In

VIEW
Certified

The MSM310 is a Wi-Fi Alliance authorized Wi-Fi CERTIFIED 802.11a/b/g product. The 
Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance. The MSM310 is 
certified under the SpectraLink Voice Interoperability for Enterprise Wireless (VIEW) 
Certification Program when it operates in autonomous mode or in controlled mode in 
conjunction with an MSM7xx Controller. 

MSM310 Access Point Quickstart

This Quickstart shows you how to get started using the MSM310 Access Point (US J9374A/B, WW J9379A/B). 

After reading this Quickstart, you can visit www.hp.com/go/procurve/manuals and download documents of particular interest such as the 

MSM3xx / MSM4xx 

Access Points Management and Configuration Guide

 and the 

MSM7xx Controllers Management and Configuration Guide

Hardware overview

Package contents

MSM310, documentation, two 2.4-GHz (2-dBi) / 5-GHz (2-dBi) dual-mode omnidirectional 
antennas.

Reset button

Press and quickly release the button to reset the MSM310. To reset to factory default 
settings, press and hold the reset button until the status lights flash three times, then 
release. For details, see 

Resetting to factory defaults 

in the 

MSM3xx / MSM4xx Access 

Points Management and Configuration Guide

.

Note:

To reconnect to the management tool after a factory reset, your computer must be 
connected to Ethernet Port 1.

Radio and antennas

The MSM310 has a single radio with two antennas for diversity. 

The antenna connectors are reverse-polarity SMA jacks. Antennas or cable connectors must 
use RP-SMA plugs. Antennas can be mounted directly on the MSM310. When a single antenna 
is used, it is recommended to connect it to the Main antenna connector.

Optional external antennas are available from HP ProCurve. On the HP ProCurve Website, see 
the 

Accessories

 section for the MSM310.

Ethernet ports

The MSM310 has two 10/100 Mbps Ethernet ports with RJ-45 connectors. Port 1 supports 
Power over Ethernet (PoE) 802.3af. In controlled mode, Port 1 should be used. In 
autonomous mode, Port 1 or Port 2 can be used.

Summary of Contents for MSM310







Reviews: