background image

Sliding rack-mount kit installation

Introduction

This document describes how to install the sliding rack mount kit on an HP Z600 Workstation and an
HP Z800 Workstation. It also describes how to install the workstation into a rack.

For Legacy Rack Customers:

Owners of earlier model racks (E3660B, E3661B, E3662B, E7590A, J1450B or J1487A/B) must also
purchase the HP Legacy Rack Adapter, part number WD587AA, to install the sliding rack mount kit.

Kit contents

This product includes the parts needed to install the sliding rack kit in HP round hole and square hole
racks, earlier HP racks, and some third-party racks, including some racks with threaded holes. The
following list describes all of the included parts; however, not all parts are used with every application.

A.

 Outer slide assembly (2)

B.

 Inner slide assembly (2)

C.

 Flange (2)

D.

 M4 screw (8)

Earlier HP racks and third party racks

Parts for installing the sliding rack mount in HP legacy racks are sold separately in adapter kit part
number WD587AA. This adapter kit includes these parts:

AA.

 Front bracket (2)

BB.

 M5 screw (4)

CC.

 M6 screw (2)

DD. 

 Adapter bracket (2)

(Required for earlier HP racks
only.)

© 2009 Hewlett-Packard Development Company, L.P. Printed in the U.S.

ENWW

Introduction

1

Summary of Contents for Z600 - Workstation - 6 GB RAM













Reviews: