background image

1

Issue: 02
Part Number:  31500DAE
Date:  2020-03-23

SmartLi-80Ah Quick Guide

Copyright © Huawei Technologies Co., Ltd. 2020. All rights reserved.

1

Overview

Model

Capacity

Weight

Dimensions  (H x W x D)

Configuration  type

SmartLi-512V-80AH-
F-01

80 Ah

< 800 kg

2000 mm x 600 mm x 
850 mm

With an LCD

(master  cabinet)

SmartLi-512V-80AH-
S-01

Without an LCD  
(slave  cabinet)

Front View

Rear View

End pressure  gauge

Battery  circuit breaker

Monitoring  interface  unit

Battery  monitor  unit 

Battery  module

MDU

Auxiliary
wrench

Fire-trace 

tube

Fire 

cylinder

Fuse

1. Before  installation,  read  the user manual  carefully  to get  familiar  with product  information  and 

safety  precautions.

2. Use insulated  tools  during installation  and  operation.
3. Only Huawei  engineers  or engineers  certified  by Huawei  are  allowed  to install,  commission,  and 

maintain  the battery  cabinet.  Otherwise,  personal  injury  or equipment  damage  may  occur, and 
the resulting  battery  cabinet  faults are  beyond  the warranty  scope  of Huawei.

4. This document  describes  how  to install  a single battery  cabinet.  For details  about  how  to install 

parallel  systems,  contact  Huawei  technical  support.

Summary of Contents for SmartLi-512V-80AHF-01
















Reviews: