background image

All Products limited to Vehicle Tow Rating, see Vehicle Owners Manual. See www.huskytow.com for Warranty 
Information / Tech Support / Product Updates. ©2017 DTS Mfg. All Rights Reserved. April 4, 2017-Rev14 

Page 1 of 8 

Assembly, Installation, Operation and Maintenance Instructions

 

Kit, Base Rail Bracket   

Part # 31564

 

 

 

APPLICATION:  2004 – 2014 FORD F150 PICK-UPS 

NOTE

: This bracket kit is to be used with the 31323 4 Bolt Bed Rail Kit or 30686 10 Bolt Bed Rail Kit. 

 

Item No.

Description

Quantity

1

Driver Side Front Bracket

1

2

Passenger Side Front Bracket

1

3

Driver Side Rear Bracket

1

4

Passenger Side Rear

1

5

Rear Mounting Strap

2

6

1/4" Spacer Plate

4

7

1" Spacer Tube

4

8

Ø5/8" -11 X 3.25" Grade 5 Hex Head Bolt

4

9

Ø5/8" Flat Washer

4

10

Ø5/8" - 11 CLIP NUT

4

11

Ø5/8" Lock Washer

4

12

Ø1/2" -13 X 4-3/4" Grade 5 Hex Head Bolt

4

13

Ø1/2" Flat Washer

4

14

Ø1/2" -13 Nylock Nut

4

15

Ø7/16" -14 X 2"  X 1.41" U-Bolt

2

16

Ø7/16" Flat Washer

4

17

Ø7/16" Lock Washer

4

18

Ø7/16" -14 Grade 5 Hex Nut

4

19

Pull Wire

1

COMPLETE PARTS LIST

 

 

                             

Dealer / 
Installer:   

Provide a copy of these Instructions to the end user of this product. These Instructions provide 
important operating and safety information for proper usage of this product.  Demonstrate the 
proper use of the product with the end user.  Have the end user demonstrate that they understand 
the proper use of the product.  

End 
User:  

Read and follow all instructions included in this manual.  Ask your Dealer / Installer for assistance 
if you do not understand the proper use of the product.  Never remove any decals from the 
product.                                           

Center

 

Bolt

 

Kit

 

32059

 

(sold

 

separately)

 

must

 

be

 

used

 

when

 

towing

 

with

 

a

 

26K

 

hitch,

 

Goose

 

Neck,

 

or

 

Maneuvering

 

System.

 

 

WARNING!

  Never exceed the towing capacity of the 

tow vehicle. 

Tools Required

11/16" Socket & Wrench

3/4" Socket & Wrench

15/16" Socket & Wrench

Torque Wrench

Safety Glasses

CAUTION

: Do not install base rails over plastic bed liners. 

Plastic bed liners must be cut out of the way. Rails may be 
installed on spray in liners. Consult spray liner installer for 
recommended curing time.

Base Rails Not Included 

 

Summary of Contents for 31564









Reviews: