background image

                        0663 Model L&H                          

IBM OEM StorageProducts

FEATURES 

Industry-standard interface:  ANSI/SCSI-2
Integrated controller
1,004 MB formatted capacity (512 & 520 bytes/sector) (models H12 and   L12)
Logical block addressing
Implied seeks
SCSI disconnect and reconnect capability
SCSI bus parity
1:1 interleave
High performance (H12 & H11) and low power (L12 & L11) models   available
(0,4/4) 8/9 rate encoding
Media data transfer rate:  3 MB/S
SCSI data transfer rate:  up to 10 MB/S (synchronous)
256K byte dual-ported data buffer
Read-ahead caching
Multi-segmented data buffer
Scatter/Gather function support
Tagged and Untagged command queuing (selectable)
Automatic sector reallocation (selectable)
Error logging
Variable logical block lengths (256-6000 bytes with exceptions)
Down-loadable SCSI firmware
Automatic retry and data correction in read errors
In-line alternative sector assignment for high performance
Sector reassignment without reformat
Predictive Failure Analysis

 PERFORMANCE 

Data transfer rate

   Buffer to/                    3 MB/S (instantaneous)
   from media
   Host to buffer             up to 5 MB/S (synchronous)
   Host from buffer        up to 5 MB/S (synchronous)
Rotational Speed            4316 RPM
Average latency             6.95 mS
Seek time                        Read           Write
   Single cylinder            0.6 mS         2.5 mS
   (all models)

Summary of Contents for 0663 Series

















Reviews: