background image

 

 

ICC - Model VIP+   

Positive Pressure Chimney System  

and Grease Duct 

 

INSTALLATION AND MAINTENANCE INSTRUCTIONS

 

Scope and Recommendations 

The  ICC  Model  VIP+  is  a double  wall  construction  listed  venting  system  designed  for  venting boilers,  engines  and  other 
commercial and industrial heating appliances.  Positive pressure piping system up to 60"  w.c. (15 Pa.).   

 

Listed Models :

 

VIP+ Double Wall Air Insulated Chimney (1” Air Space) 

 

 

 

VIP+ Double Wall 1" Fiber Insulation 

 

 

 

VIP+ Double Wall 2" Fiber Insulation 

 

 

 

VIP+ Double Wall 4" Fiber Insulation 

 

Sizes:

   

Ø6" (152mm) to Ø24"  (610mm) Flue Diameters

 


 

WARNING 

 

A  major  cause  of  vent  related  fires  is  failure  to  maintain  required  clearances  (air  space)  to  combustible  materials.  It  is  of  utmost 
importance  that  this  venting  system  be  installed  only  in  accordance  with  these  instructions.  Do  not  fill  the  air  space  with  insulating 
material.

 

 

Contact local building or fire officials about restrictions and installation inspection in your area. 

 

Do not begin installing the ICC Model VIP+ venting system until you have carefully read the appliance and vent system installation instructions. 
 

Use only ICC Model VIP+ components. Failure to do so will void the certification and warranty of the product. 
 
Keep these installation and operating instructions in a safe location for future reference. 
 

 

Examine all components for possible shipping damage prior to installation. 

 

Proper joint assembly is essential for a safe installation. 

 

Follow these instructions exactly as written. 

 

Check tightness of joints upon completion of assembly. 

 

This venting system must be free to expand and contract. 

 

This venting system must be supported in accordance with these instructions. 

 

Check for unrestricted vent movement through walls, ceilings, and roof penetrations. 

 

Different Manufacturers Have Different Joint Systems and Adhesives. 

 

Do Not Mix Pipe, Fittings, or Joining Methods from Different Manufacturers. 

 

 

Tested and Listed to: 

 

UL-103 , UL-2561 , ORD ULC C-959 , UL-1978 , ULC-S662 
by Underwriters Laboratories, Inc (Listing # MH16722) 

 

 

 

ICC INDUSTRIAL CHIMNEY COMPANY INC

 

400 J.F. Kennedy, St. Jérome 

Québec, Canada, J7Y 4B7 

Tel.: (450) 565-6336 
Fax: (450) 565-6519 

 

www.icc-rsf.com 

 

 

VIP+_2016-04 

 
 

Summary of Contents for VIP+ Air Insulated































Reviews: