background image

USER'S MANUAL

CAUTION

Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.

Serial Number Decal

Model No. NETL11520 
Serial No. 

Find the serial number in the location
shown below. Write the serial number
in the space above for reference.

www.iconeurope.com

Visit our website at

Part No. 183913 R0602A

Printed in USA © 2002 ICON Health & Fitness, Inc.

ORDERING REPLACEMENT PARTS

To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write: 

ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road, Beeston
Leeds, LS11 8JG
UK

Tel: 

Fax: 0 (044) 113 387 7125

When ordering parts, please be prepared to give the following information:

• the MODEL NUMBER of the product (NETL11520)

• the NAME of the product (NordicTrack

®

2500 R treadmill)

• the SERIAL NUMBER of the product (see the front cover of this manual)

• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on pages 30 and 31 and the EX-

PLODED DRAWING attached in the centre of this manual)

08457 089 009

QUESTIONS?

As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:

Or write:
ICON Health & Fitness, Ltd.
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds
LS11 8JG

email: csuk@iconeurope.com

08457 089 009

Class H Fitness Product

Summary of Contents for NordicTrack 2500 R



















Reviews: