background image

STANDARD REGENAIR BLOWER

O

PERATION

& M

AINTENANCE

M

ANUAL

Thank you for purchasing this Gast product. It is manufactured to the highest standards

using quality materials. Please follow all recommended maintenance, operational

and safety instructions and you will receive years of trouble free service.

General information

This manual does not apply to:

• SDR Series blowers without motors

• Blowers powered with Explosion Proof Motors

www.gastmfg.com

ISO 9001 & 14001 CERTIFIED

®Registered Trademark/™Trademark of Gast Manufacturing Inc., Copyright © 2002 Gast Manufacturing Inc.  All Rights Reserved.

PART NO. 70 - 6000 F2-200 (REV-L)

Model R1 Shown

Model R6P350A Shown

Model R7P Shown

Product Use Criteria:

• Pump only clean, dry air.

• Operate at -20ºF - 104ºF (-29ºC - 40ºC).

• Protect unit from dirt & moisture.

• Do not pump flammable or explosive gases or

use in an atmosphere that contains such gases.

• Protect all surrounding items from exhaust air. This

exhaust air can become very hot.

• Corrosive gases and particulate material will

damage unit. Water vapor, oil-based contaminants

or other liquids must be filtered out.

• The blower must be installed with the properly sized inlet and inline filters, gauges and

relief valves to protect the product from dirt and over-heating.

• Consult your Gast Distributor/Representative

before using at high altitudes.

1

WARNING

PLEASE READ THIS MANUAL COMPLETELY BEFORE INSTALLING AND USING

THIS PRODUCT. SAVE THIS MANUAL FOR FUTURE REFERENCE AND

KEEP IN THE VICINITY OF THE PRODUCT.

Summary of Contents for GAST R1













Reviews: